Hello,
In ncs, I am working with \nrf\samples\ipc\ipc_service. I want MCUboot to build \nrf\samples\ipc\ipc_service\remote to run on nrf5340 CPUNET. When I CONFIG_BOARD_ENABLE_CPUNET...
Hi,
I am currently conducting measurements using channel sounding with my nRF54L15 boards. I am at the end of my master thesis, so there is not so much time left to really...
The nrfx pwm supports a number of events for a callback: /** @brief PWM driver event type. */ typedef enum { NRFX_PWM_EVT_FINISHED, ///< Sequence playback finished. NRFX_PWM_EVT_END_SEQ0...
Hi,
I have two nRF5340 DKs and want one to be server, one be client. I use NCS offcial code and simply buide them, however, " LED3 starts blinking green on every device...
Hello,
I have been working with the nRF9160 DK to understand AT commands. I tried flashing the Serial LTE Modem application using the Quick Start option in the nRF Connect...
Hi everyone,
In nRF9160 with ncs 2.9.0 I've problems when trying publish a MQTT payload bigger than 2700 bytes aproximately. In advanced I already was adequated buffer size...
hello there i downloaded nordic's new mesh sdk. i am using nrf51dk. in mesh sdk there is no keil project . only source file is given. can you tell me how to make project using...
Dear Nordic-Support,
my questions are in regard to the nRF52840 PDK and the SPIM-frequency rates.
The Objective Product specification lists possible configuration...
I would like to use an nRF52840 as a sniffer between my phone and an other nRF52840. I tried to follow the nRF Sniffer guide 2.1 but the firmware seems not working as LED1...
Hi everyone,
I am trying to advertise data from nrf52832 to a smartphone (nRF Connect).
Below are my advertising parameters.
ble_adv_modes_config_t options = {0};...
Hi,
What is the max timer frequency that the nrf52840 can handle in counter mode?
I see that the timer runs at max 16Mhz when in timer mode, is it possible to get 32Mhz...
Ok I’m new to ARM / Nordic and Bluetooth but after a bunch of reading I downloaded SES and the Mesh SDK and got the light switch demo to both compile and run on a few boards...
I'm looking for where the compiler is for the nRF52832....
I just need to compile code, and copy the binary to the device....do you have any pages which show, step by...
hai. I got thingy 52 from Nordic tech tour. now i would like to reconfigure it. for enabling all its sensor into RTOS(real-time operating system apache mynewt) with the nrf52...
I want to implement a ready line for SPI and I noticed nordic has similar code in your sdk: components/serialization/common/transport/ser_phy/ser_phy_spi_slave.c.
However...
Hi,
I am trying to send data to server using ESP8266 WiFi module interface with nRF52832 DK board via UART interface. My problem is when i sent AT command to ESP8266 it...
Hi,
I have a project with 52810, I met below build error when compiling dfu project:
.\_build\nrf52832_xxaa_s132.axf: Error: L6366E: uECC.c.o attributes are not compatible...
Hi
Now I'm using nRF52810 base on SDK v14.1 and I want to do the OTA for it. When I combile the bootloader project, I get so many error "No space in execution regions....
I just want to change the Advertising interval min and max values in ble_gap.h file in meta wear RG
so do I have to change firmware code or is there any other way to deal...
