در دنیای پررقابت صنعت غذا، موفقیت رستورانها، هتلها، تالارها و آشپزخانههای مرکزی وابستگی زیادی به کیفیت و کارایی تجهیزات آشپزخانه صنعتی دارد. برخلاف آشپزخانههای خانگی،...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
Dear Sir,
I am interfacing nRF24L01 with Renesas R5F104 Microcontroller on transmitter side and my Reciever is nRF24L01 interfaced with Arduino Uno Board.The Transitter...
I am very new to this so apologies in advance .
When I compile the sample code using Keil for the Thingy i get the error message.
.\_release_v1_0_0\app_thingy_s132...
hi, I am updating the sdk from 12.2.0 to 14.2.0, and using softdevice s132. I get a problem by connecting device using ios devices, but it works fine with android device....
Downloaded the S132 from the NRF52840 site and loaded it onto the NRF52840DK board using NRFgo studio.
Then created a new project in CrossStudio. Imported the memory map...
Hello guys,
I wanted to start to implement the power management feature on the NRF52 using the Zephyr kernel for a bluetooth application. Unfortunately I am running in...
Hi,
Do you know when the PWM or the ADC functionality will be added to Zephyr for the nRF52 chips?
Can we use the nRF SDK inside a Zephyr application to use unimplemented...
Hello,
sorry to have to ask again, but from reading through all the posts I could not quite figure out how much current the SPI should draw when it is active and reading...
Hello everyone,
I am looking forward to 3rd party BLE modules in which I am interested in choosing Taiyo Yuden EYSHCNZWZ
I want to know that can we flash our code using...
I am using 3 nrf52 DKs with S132 and SDK14 / and SDK15 to try and implement a combination of the multilink and UART examples. I started with the ble_app_uart_c example and...
Hi All,
We are working on nRF52810 chip for on of our beacon project and we are using external antenna on board but
We are dealing with the Reason 8 disconnections.
...
Hey Team,
Can anyone please share the layout of the Program and Debug connector on the Thingy? I don't have a 10 pin SWD connector readily available and need to start...
Hi everyone, I have configured the LOG module to use it with the UART in view of debugging. I don't send anything in my loop but the UART send constantly these data :
<info...
