Steps to reproduce the problem
Create a new application based on the Matter Light Switch example of the SDK 3.0.2
In prj.conf set CONFIG_CHIP_FACTORY_DATA_BUILD=n
...
I would like to do a FOTA using bluetooth and external flash memory on nrf52840 board. I am also using sdk 2.9.1 The issue i am currently facing is I get the below when i...
Hello nordic community,
i have custom board that have nRF5340 and nRF7002, our requirement is to use wifi every 5 minutes (connect send data and disconnect) but randomly...
HI,
I am using the periodic_adv_rsp example from version 3.0.0. I would like to ask how to switch channels and transmission power in the example code?
Thanks.
In our development using NCS-2.6.1 it is desirable to have logs using BT NUS.
"Serial Bluetooth Terminal" android application is used.
For testing purposes NCS\v3.0.2...
Hi all.
Just wondering if i need to go through the tutorials on making a service if i just want to read a few bytes in an advertising beacon.
I'm a little lost on figuring...
Hi ,
I am using a bluetooth peripheral which have the Custom Service ID and characteristics ID as below.
Service UUID: 56494B01-0100-1000-8000-00805F9B04E1
Characterisitics...
Hi,
We are currently developing an application that makes use of soft device(s112). We tried using timer(Timer 1) for a timed wake up and sleep but found that the actual...
We are seeing an LMP PDU error when connecting to a Nexus 6p with Oreo (8.0.0) when connecting to an nRF52832 utilizing SDK 14.2 and either s132 vs 5.0 or 5.1 anytime NRF_SDH_BLE_GAP_EVENT_LENGTH...
Been testing custom_ble_service_example , specifically to see if a two byte custom_value can also be used.
But when setting custom_value to uint16_t I get a warning at this...
Hi, I would like to use a PWM application with mesh SDK. However when I try to compile, I got an error because "app_pwm.h" is missing (No such file or directory). The only...
Hi !
I'm using the nrf52832 chip and I'm trying to communicate with a LIS2DH12 accelerometer using the I2C protocol.
But unfortunately I can't handle with it, it seems...
Hello,
I am completely new to creating a Bluetooth mesh network and nRF5 devices. I have three nRF51 DK and 2 nRF51 dongles. I have earlier read the posts and made nRF51...
Hello,
I am using sdk12.2.2 and customised nrf52 board. I am writing 6000 records of 24 bytes each in flash of nrf52. My challenge is after 6027 records I am getting error...
i made custom board refer to thingy 52 Circuit
all fuction circuit is same so i want to use thingy 52 firmware
when i was erase all memory nrf52832 and upload thingy_v2...
I am using nrf52832 sdk14.2.0 to develop now, I want to realize the following function on the basis of PWM_driver example, output the following waveform on P0.22: 1ms high...
Hi all,
I am newbie with nordic, and I need some help.
I am using nRF52832 with softdevice.
I need to generate a 128 kHz clock signal (PWM pulses with 128kHz frequency...
Hello,
I'm doing some power evaluation of the three PHYs of BT5 using the PCA10056 preview (v0.9.0) and the PPK (rev 1.1.0), moreover I'm using the ble_app_att_mtu_throughput...
I've seen variations on this question, but never quite been able to decipher a complete answer:
I've built an app for the NRF52DK based on the nRF5_SDK_15.0.0 "Hello World...
