Hello, I'm running an example of channel sounding using nRF54L15.
The build is fine, but the following error occurs during flash.
Python is using 3.12.4 version. As you...
Hello,
I'm here again because this time I need to autoconfigure (configuring from inside program, no use of any nrf app) heartbeat destination node and source node.
For...
We have developed an application which uses the nRF9160 together with the same GPS and Ethertronics/Kyocera/AVX antennas as that of the nRF9160-DK . For the LTE antenna, we...
We're trying to measure supply current used by the NRF9151 DK but have discovered that the current measurment connector (P22) only includes current supplied to VDD, and that...
Hi，
I am using nRF54L15-DK for Zigbee light_stwitch startup testing. After successfully connecting the development board to the Hub for the first time, I evaluated the time...
I'm working on a project involving a USB dongle based on the nRF52840 SDK-2.9.1, which needs to communicate with a sensor (also an nRF52840) and transmit data via USB to PC...
Hello....
Is there a way to configure the SPI peripheral(s) to run at a custom bit rate (frequency)?... For example: Run SPI at 3.4MHz.. or any other custom frequency that...
Hello all,
Do you advise to have 2 SPI interfaces - one for the sensors we're using (accelero/ gyro) and another one for the SD card? if so, when adding an SD card to our...
Hi team,
i am having a custom board i want to program soft device and application using external j link. i came across nordic website in this page http://infocenter.nordicsemi...
Hello All,
I am a beginner to NFC OOB, so can you suggest me some good learning materials regarding NFC OOB pairing as I wish to do so between my mobile phone and the...
Good Morning Team,
Hope your day is going well!
Could you please provide the IPC 1752 document and RoHS CoC (2015/863/EU) directive document for below part since it is...
hi hi ;
i'm trying to control gpio pin 20 with my smart phone and with event at gpio pin 5 (when the state of the pin 5 changes the gpio pin 20 toggeles ) but my problem...
Hi, can someone explain in simple terms how it works?
I don't really have a clear concept of what a replay attack is, but I suppose it has something to do with recording...
Hi,
I am facing the same issue for all of the node.js examples.
It says: Connected! Error: command disallowed (oxc)
Also is says: Service uuid XXXXXXX not found!
...
The nRF52 SDK ANT example "ant_scan_and_forward/" configures a device linit of (16-1)=15 in this line:
// Public Definitions #define MAX_DEVICES ((uint8_t) 16) /**< Maximum...
On nrf52832 and nRF5 Mesh1.0.0
When running idle state(not RX/TX), current comsumption is over 400uA.
And every 100ms, CPU is wake up.(small working.)
What happen...
Hello! I am using application that support ANT+ and BLE, so i am using s332 softdevice. now I want to add BLE bootloader feature. (send .bin via BLE). but in SDK v13.0.0-1...
Hello.
Which application can I use to monitor and configure a smart wristband with nRF52832? I would like to check its firmware, update it and see all the info about the...
Hello. I've got issue with TWI and power down mode. I modificated "ble_app_bps" example, prepared own service and characteristic and I added BME280 sensor. And almost everything...
Dear Nordic guy, I'm developing with nrf51822(6.0 stack binary and 5.0 sdk)
I have one question regarding clock.
As I know,automatically,stack go to the sleep mode(HF clock...
