Environment info:
Tested on own integrated product, and nRF5340 Audio DK.
Firmware built on Fedora Linux 42,
Using the Rust programming language, using embassy-nrf &...
Hi Nordic team,
I’m currently testing UART communication on nRF54L15 with NCS 2.8.0 , and I’ve encountered an issue I’d like to ask about.
When using UART20 configured...
Dear Nordic Semiconductor Support Team,
I hope this message finds you well.
I am currently evaluating the nRF52840 for use in an industrial/automotive application and...
Hello,
I've tried to compile the experimental_ble_app_hrs_pairing_nfc example using Keil uVision. The example requires the NordicSemiconductor::nRF_DeviceFamilyPack version...
Hello,
This ticket actually build upon the previous ticket I did here Possible Bug: Cellular modem sample with nRF9151 running SLM .
To recap, running cellular modem...
Hi,
I'm trying to use MBEDTLS with MBEDTLS_USE_PSA_CRYPTO and CONFIG_PSA_CRYPTO_DRIVER_CC3XX activated.
Unfortunately I can't find a way to tell MBEDTLS that nRF9151...
The 9161 has 256 KB of RAM, but while building the application, it reports that only 32 KB is available for the application. If I create some large static buffers (e.g. 10...
Hello,
I am currently using the `AT%XICCID` to obtain the ICCID of Hologram eSIMs. The output of some of these eSIMs are just the raw 20 digit ICCID with no ending checksum...
Hi,
I’m looking for your recommendations on a suitable conformal coating for an application subject to high humidity. The goal is to mitigate any potential risk of short...
Hi I am trying to get an SD card hooked up to my nrf52840 devkit. I am using nRF Connect v2.6.1 and I was trying to get the sample code working, so I used the sample in ncs...
I have downloaded nRF connect setup V5.1.0 and nRF command line tools V10.24.2.
downloaded nRF connect extension , SDK pack and tool chain in VS code.
I added the build...
in this example:
https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/bluetooth/conn_time_sync/README.html
the peripheral has this assert statement when...
Our design has an nRF5340 with RV3028C7 to provide the 32 kHz clock via P0.00.
If I configure P0.00 as a digital input, I can see the pin toggling.
However, if I use the...
Hi
Is it possible and what is the correct way to implement main clock trimming at runtime? Which NCS version this works on?
I see there is already some setup going on...
Hi,
I want to write data to a specific memory. I understand there is ZMS.
https://docs.nordicsemi.com/bundle/ncs-latest/page/zephyr/samples/subsys/fs/zms/README.html#zms...
Hi,
I am trying to build memfault sample as in intermediate course, after hello_world project configuration and prj.conf options addition, i get following build error...
Setup: NCS v2.8.0 nRF52840
Hi,
I would like to ask about the implementation of Zephyr's SAADC driver (` adc_nrfx_saadc.c `).
In the project I'm working on, I need to...
Hello everyone,
I have an nRF5340 microcontroller (NORA B106 module), and I want to connect a square wave signal to one of its pins to read its frequency or count the number...
Dear Nordic:
I used V2.8.0 SDK to build light bulb, and I have commissioned bulb A(node id: 11) and bulb B (node id: 11) successfully!
Then I used below command to add...
Hi,Team,
I'm using the nrf54l15-dk to develop zms to save custom configurations without affecting the pairing information of ble.
So I have a few questions: 1.Is the storage_partition...
I am trying to set up FOTA support with external flash for mcuboot secondary partition. I have gone through several tickets on the subject, but haven't been able to solve...
We are currently using ncs 2.9.0 on an nRF5340. We use the BT_HCI_OP_VS_READ_VERSION_INFO to determine at runtime what version of the BLE stack is present. This information...
