I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hi,
Quick question: I read in this article on the section "A tough world of lighting controls" it states the following: "Let's say that five messages are spaced 20 ms apart...
Hello everyone ,
We are able to read out ADC values(if i connect battery positive externally on ADC pins). i wanted to know if there is internal connection provided to any...
Hello,
Testing your nRF Connect with a BLE Thermometer. I was able to connect and read data.
Can you help me with one question I have ?
This is part of the log file...
Where to start? Is it possible?
I need to send data between the two chips using 802.15.4.
There is no need to form a network.
I was looking at the Wireless Uart example...
Hello all,
We want to run the example TCP-Client example from IOT SDK.
how should we proceed for the same ?
Which softdevice must we use ?
Thanks and Regards ...
Hi,
My setup:
* nRF52 DK
* nRF5_SDK_15.0.0_a53641a
* s132_nrf52_6.0.0
* SES V3.34b 64-bit.
I am struggling to properly use FDS module. I am using multiperipheral...
Hi Support Team,
By testing SDK15.0.0/Serial DFU, I find that if we use non-default baud rate(115200), such as 9600 or 38400, we have to assign a non-zero value to -prn...
Hi everyone,
I have 2 boards that I've been using for testing. One is the NRF52 DK with the nrf52832 and the other is a simple custom board i made with an nrf52810.
I...
Hi all,
I'm currently making Mbed OS 5 able to work with the NRF51 with DFU enabled. It seems Mbed OS 5 currently has no support for a Nordic bootloader for the NRF51. Mbed...
Hi Guys,
I'm using SDK 15 Version and Nrf52832 DK.
now i want to use second uart when one uart is communicating with the PC Via CLI.
How Can i make it???
Thanks in...
Hello everybody,
I use NRF52832, sdk14.2, s132 softdevice. When I install SDK examples(for example nRF5_SDK_14.2.0_17b948a\examples\ble_central\ble_app_uart_c), the minimum...
Hello , we are in the production phase, I use us addess mac(If I bought unique MAC address from IEEE. ) so our factory asks for the registry that will be configured, so is...
I want to add the UART peripheral code to the Mesh Light Switch example in latest MESH SDK v2.0.1 .
I have tried to add all the UART code to the Mesh Light Switch Client...
I'm trying to get acquainted with the NRFX_GPIOTE driver by writing a program to do the following:
initialize TIMER to generate three compare events:
channel0 compare...
