Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi everyone, I'm trying to implement a simple bluetooth beacon which broadcasts / advertises the number of button presses and the time in seconds after the last button press...
Hi everyone,
I'm trying to change the advertisement data while advertising using an interrupt. So far I've managed to use a button to change the advertisement data.
...
Hi,
I have huge BLE carrier frequency drift, which cannot pass FCC requirement.
The drift is 256kHz which seems not normal.
I'm using 32MHz 10ppm xtal so drift should...
Hi!
My setup:
* nRF52 DK
* nRF5_SDK_15.0.0_a53641a
* s132_nrf52_6.0.0
* SES V3.34b 64-bit
In my application I am using Peer Manager to manage bonding and also...
Hi all
The errata sheet V1.8 states that the errata 143 applies also for the Bluetooth Low Energy mode. Does that mean that the BLE stack of the SoftDevice S132 is also...
Hi,
I am using nRF52832 DK and other same custom board, sdk v15.0 with SES IDE. My application like this:
For ble peripheral used example ble_app_uart and for central...
Hi Sir,
In my system (windows 7), I had install the GCC 4 .9 2015 q3 for SDK 14.2.0/12.3.0.
As reference the release note of SDK 15, the GCC upgrade to 6-2017-q2-update...
Good Morning Team, Hope your day is going well! Can you please provide the Full Material Disclosure (FMD) document for below part since I could not locate it on website. ...
Hi, I am merging the multilink example and the CDC ACM example in SDK15.
However, if you merge and run it, it will continue to fail.
Here is the source.
I have...
Hi, i am using a model based on simple_on_off model to send custom messages.
For now provisioner and client are separated as in the V2.0.1. I tried to combine them first...
Hi,
Is it OK to use the Nordic Semiconductor ASA (0x0059) ID for broadcasting data in the manufacturer specific data field?
If so is does Nordic provide a specification...
Hello
For the BLE Mesh 2.0.1 demo i bought some nrf52840 develboards. Then i write the demo with "python scripts/quick_start/quick_start_demo.py" to the nrf52840 develboard...
Dear Nordic Team, Thanks for supporting.
I want to know the possible for mesh network concept with nRF52832 (PCA10040). If possible means guide me for startup.
Regards...
HI!
I'm a happy owner of two nRF52840 Preview DK board (v0.9.3). I'm considering to change their chips to production versions. I found that schematics and PCB layouts are...
Hi,
We are using nRF52832 for one of our central device. Our peripheral is also based on nRF52. We are facing issues while scanning for the peripheral from the central side...
