Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
I'm evaluating BT5 feature using the PCA10056 preview dev kit and SDK v15.
When working with LE Coded PHYs, is the S2 or S8 version? In the SoftDevice release notes only...
Hello,
I'm testing the bootloader with SDK v.15 and I found a state when DFU won't resume (on BLE transport).
I crashed nRF Connect randomly, in that case, between the...
Hi All,
I am designing circuit to Turn ON 4 LEDs at a time based on high and low of GPIO
Supply voltage is 3.3V my doubt below circuit is fine whether it will work fine...
I try onnrf52804 (nrf52840-DK) with SoftDevice V6.0.0
----------------------------------------------------------------------------------
ble_gap_scan_params_t s_scan_params...
Hi all,
I want to use the python scripts provided in application notes in nordic documentation to run DTM example flashed into nRF52840 SoC. So when I open command prompt...
In the infocenter, after searching for something, if you click on an item in "Search Results" (left hand panel), it brings up the associated page in the right hand panel....
Hello all,
I'm trying to do a "BLE scanner" in order to read non connectable advertisements. These advertisements can be PHY_CODED and PHY_1MBPS (classic BLE advertisements...
Hi everbody,
I'm using the BLE Database Discovery module to discover services and characteristics of a BLE peripheral. This works fine, except for one strange quirk:
When...
Dear Nordic Support Team,
I’ve bought an evaluation kit here : http://t-yuden.com/ut/product/category/module/EYSHJNZWZ.html
and i would like to program the chip, so i...
Hi,
I am scanning from my nRF52840 and connects to one peripheral and i have written code to get it's Device information(DIS) and i stored all these information in some...
I'm having trouble maintaining a connection between my nRF52832 and Raspberry Pi. I followed the step by step guide (making sure to use the correct IOT SDK for my board),...
I am gaining my expertise in Nordic. After learning from tutorials. most of the tutorials mentions to use master control panel. But I cannot able to scan using master control...
Hi!
I am currently developing an application for nrf52832 and am using the uart module with retarget.c for output over uart via printf().
Now a few days ago I added...
Hello everyone ,
We have done advertising and scanning(both in a single firmware) on nrf51822 using QFAC chip. using SDK 12. Now we want to switch our code to NRF51822 QFAA...
hi
I am trying to add Manufacturer specific data
ble_advdata_manuf_data_t manuf_data; // Variable to hold manufacturer specific data uint8_t data[] = "A"; // Our data...
