I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
On SDK 14.x.0 only
Please Do not judge the quality of SDK based on number of entries here. This thread should be considered as part of Nordic effort to find issues and...
We are using SoftDevice: sd132 v 5.0.
With event "BLE_GATTS_EVT_EXCHANGE_MTU_REQUEST", the function "sd_ble_gatts_exchange_mtu_reply" always return with "NRF_ERROR_INVALID_STATE...
I am using Fansttel BT832X SoC with SDK 14.2 ( Soft Device Version S132 5.0 ). i have configured PA/LNA mode in BT832X module. If i use only BLE advertisement i can see the...
Hi,
We want to update nrf52832 via uart. We have host controller and want to upgrade nrf52832 through it. We have SDK BLE_2.0.1 for the mesh. I had gone through DFU Example...
Hey,
I have a smart kettle Redmond RK-g201s, which is controlled by bluetooth. I have read that it has nrf51 SoC. It has 1 service with 2 characteristics: for read and for...
Hi Nordic:
I want to consult one question about "BLE HID Keyboard". I am trying to use the product---nRF52832 to make the "BLE HID Keyboard".
Then I download the source...
Hello Nordic Team,
I have some issues with the PPK since i uptdated nrfconnect from 2.0 to 2.4.
I get this error message when I try to select the serial port on Power...
I have some working knowledge of Android but I'm new to Fragments, Injection, Binding, ButterKnife .etc. I have gone through some videos and tutorials but can't catch where...
Hi,
I am using the nRF52832 DK for connecting and collecting the data from multiple beacons simultaneously. Right now i use the nRF_Connect desktop application for collecting...
Hi,
We have a nRF51822 project based on ble_app_hids_keyboard, SDK 12.3. When using Keil, it runs well. However, when using arm-gcc to compile the same code, something wrong...
Hi,
I am currently exploring the USB_CDC_ACM examples as well as the NFC record launch app.
Individually, I can make the examples run fine.
Then, I tried to combine...
Using nRF52840 SDK 15.0.0 with SoftDevice
I am trying to protect the Access Port, used to do it using the following command
nrf_nvmc_write_word(NRF_UICR->APPROTECT, 0xFFFFFF00...
Hi,
I'm using the NRF52840 SDK version V15. My program uses:
1. softdevice (BLE communication)
2. SPI uses using SPIM interface in nonblocking mode.
3. Timer event...
I am trying use DFU example with Mesh sdk 1.0.1, however following the start DFU guide, i have some question, if i have two DK52 one of them must be programmed with the original...
