Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
It is said that ble5.0 can cover a range of 300m, I wonder how big is current when this is achieved? For 52840, the largest power output is 8dBm, for 52832, the largest output...
Hi,everybody!
I use nRF52832,supply volt 3.0V normal, program can be downloaded , run and debug,i ensure the program is accurately.To control a gpio P0.09,on the hardware...
Dear Nordic,
I debug the SDK15 example project ble_app_template_pac10056_s140 project, nothing change, but it will jump into app_error_weak.c as below picture, please help...
I can not get information about the power consumption when twi is enabled and idle. It just state the current when it is running. So do I need to disble it when it is idle...
Greetings,
We have taken the RAM Retention example and are experiencing a failure (all LEDs on) when setting MAX_TEST_ITERATIONS to a value greater than 1. This is duplicated...
I am using nrf51822 with softdevice 7.3 and sdk6. I am having some strange problems in single bank bootloader. The nrftoolbox version 2.4.0 gets stuck at 94% during the firmware...
Hi,
(SDK v14.2, nRF52832)
I'm developing a Timeout Timer functionality, and was wandering if the following scenario is a good practice:
I don't want to have a interrupt...
Good morning everyone,
I am having a lot of problems configuring the Peer Manager.
I read several discussions on the topic, but either they are old (referring to ble_evt_dispatch...
Hello everyone,
I`ve 4 thingys and ran the https://github.com/NordicPlayground/Nordic-Thingy52-mesh-demo . That works well.
Now I`m trying to add the nRF52 DK as a Node...
I am trying to perform a dfu upgrade according to: infocenter.nordicsemi.com/index.jsp
The exact command I am running is: nrfutil dfu ble -ic NRF52 -pkg dev_board_bl.zip...
There is something I want you to tell. Do you know how to allow other interrupts (specifically IRQ pin) while interrupting app_timer? I studied variously, but I can not find...
While I'm waiting on answers to other questions, I thought I would try to nrf_Logging with the Segger RTT up and running. It sounds like a pretty tool.
I have created a...
As picture, This is the external circuit of 52832, and I've drawn out P0.09,P0.10,P0.17,P0.18,P0.19,P0.22 of these six gpios, each of them for control purposes, and now P2...
Looking to make the nrf52 DK into a CR2032 coin cell battery tester. I tried a couple of sdk 15.0 examples, uart, proximity and another from a devzone case but not really...
I am using the nRF52840 development kit and running the SPI peripheral example in SDK 15.
I am having trouble displaying a static value in my watch window.
static const...
