I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Hi,
I am doing OOB commissioning with OpenThread. According to section 10.12 of Thread 1.1.1 specification, Active / Pending Operational Datasets need to be persisted to...
Hello,
I'm trying to connect external RTC, which has a 32kHz clock on it's pin to nRF52832. So far I've had issues with connecting this clock to P0.00 pin and having P0...
Hi all:
when i add uart code in ble_multilink ,and it gived me errors like this:
"<error> app: Fatal error <warning> app: System reset <error> app: Fatal error <warning...
If I put too many characters into a serial using IRQ mode, it stops reading input.
I haven't tried polling or DMA yet.
Using
nRF5_SDK_15.0.0_a53641a
gcc-arm-none...
Hi ,
can u please provide more details about error code 4, returned by ble_ancs_c_init function.
what is this error, and how to resolve it???
thanks,
amarjeet
Hi there,
we are developing an application based on simple IEEE 802.15.4 packets, for which we use the radio peripheral. Every example found in the SDK starts with switching...
Hi
I would like to perform a connection over 2MPHY instead of 1MPHY; is there an example to show this? This should be doable according to the softdevice v6.1.0 changelog...
Dear Nordic
I am doing a project that has a multilink one central and ten peripherals.
So I started with ble multilink multi role in here . I added ble_nus_c and uart...
Hello everyone,
I am developing a ble device and cant get under 7mA.
For test i used example application. BLE Beacon example. And the hardware part is realy basic. Only...
Hi,
We need to design a network with one master and 36 devices connected, with "long range" capability, exchanging sometime messages from 100 to 4000 bytes.
The number...
I understand from forum post https://devzone.nordicsemi.com/f/nordic-q-a/19250/the-number-of-central-connections-in-s140 that S140 v5.0.0 1.alpha release supports 8 concurrent...
I understand that Nordic provides a proprietary DFU via the BLE mesh. What mechanisms are in place to ensure that all packets reach their destination, e.g. acknowledgements...
-Using SoftDevice S110 8.0.0 for the nRF51822_xxAA.
-UART0 running on 19k2 without flow control (only rx/tx) and using irq priority APP_IRQ_PRIORITY_LOW (=3)
-Using the...
I'm currently porting my code from nrf52832/S132 to nrf52810/S112 (SDK14.2).
It seems that the s112 has no support for scanning, i.e., BLE_GAP_EVT_ADV_REPORT, sd_ble_gap_scan_start...
