Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hi,
I got the following hardfault when running sdk 14.2, nrf52832. Since the address shows it locates in softdevice...I do not know why. May you please give me tip? Thanks...
Hello, we have a handheld device with Microchip (ex. Atmega) Microcontroller that essentially monitors and records different environmental conditions and stores them them...
I am making PUC for sending & receiving string through ble nrf51822 to phone(nordic app) with particular user define time interval like 1 min , 5 min etc. using ble_app_uart...
I'm running \nRF5_SDK_15.0.0_a53641a\examples\ble_peripheral\ble_app_uart\pca10040\s132\arm5_no_packs and following instructions from http://infocenter.nordicsemi.com/index...
Hello,
We are using in nrf51822 in a product.
I do not understand whether by definition and, thus, always, before connecting, whether a peripheral
goes to sleep between...
Hi,
our device has a hard current limit of 2mA. Normal BLE operation is actually no problem. Connection parameters and packets/event are negotiated accordingly between master...
Hello,
I am using nrf SDK 15.0.0. I am unable to build ble_app_uart example in SES. It shows this error in the screenshot:
But i can build the same example using Keil...
Hi everyone,
I want to set LF CLK source to XTAL without softdevice. But, LFCLKSTAT value is 0x00010000(CKL RUN, CLK SRC = RC) after clock start.
So, I checked same test...
When drawing lines of equal start and end x, y coordinates the GFX library shall draw a rectangle with thickness applied. If the value of the opposing axis has a start value...
Hi everyone,
This might seem like a silly post, but this happened.
I build and ran the example QSPI code given in the sdk.
But after that if i try to run my own code...
We're writing code that does dynamic pin assignment which may change over time. This question is about how the crossbar deals with conflicting pin settings.
If I set the...
Hi Technical Team,
nRF52832DK is running on central role with the below
SDK version : 12.3 IDE :IAR
It is working (connection,just work pairing,bonding, & reading/writing...
Hi,
I have connected the components mentioned in the reference schematic from the official website to my nrf52832 chip. Is there any easy method to know whether it is working...
Hello Im preparing a device that uses nRF51422 for CE and FCC testing. I need to disconnect the antenna and put a connector in it's place for the testing. I have doubts about...
