Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi Nordic expert:
I need using PyACI to let a nrf52832 board to send a genericOn client packet to other mesh devices those have genericOnOff server model.
My environment...
Hi friends:
I've followed "DFU quick start guide" and run DFU(from mesh-sdk-2.1.1) example done, the updating time is about 3000 seconds.
(My environment is only 2 devices...
I'm implementing my own DTM mode for the nRF52832 based on SDK14.2's DTM module (ble_dtm.c). My modified version of ble_dtm.c seems to work fine, but I don't completely understand...
Good afternoon,
I am able to write data using polling mode with the macro NRF_SERIAL_CONFIG_DEF(serial_config, NRF_SERIAL_MODE_POLLING, NULL, NULL, NULL, NULL). I am using...
Hi together!
Ist it possible to send a CR (Carriage Return) over the programmable UART Buttons?
When yes, what is the Syntax for?
For example, i need to send such a...
Hi
I used nrfutil.exe (v3.5.1 based on python v2.7.13) to create bootloader.zip file from SDK v15 - \dfu\secure_bootloader\pca10040_ble\ sample code.
CMD : nrfutil.exe...
It appears as if the LFCLK is not calibrated to 500PPM accuracy. I display the time in the system and every 60 seconds it falls 2-3 seconds later relative to the clock on...
nRF52832 / SDK V15.0.0 / nRF connect / DFU OTA Buttonless
Hello,
My device name is 21 chars but it is truncated and appears as 20 chars in nRF Connect "Discovery devices...
We are using an nrf51822 processor, running off of 2.7 volts from a switching power supply, powered with 12.4volts. The processor has simple gpio connections, and a battery...
Hi,
The structure nrfx_spim_xfer_desc_t contains both tx_length and rx_length fields.
Is there a situation where tx_length != rx_length ?
Thanks,
Daniel
I have a nicely working application that occasionally hangs. I have managed to trap a "hard fault" under the debugger (using VS with GCC). I have the system halted with the...
hello, Nordic developers!
I needs help develop rnf52840.
Goal
My goal is ble & 802.15.4 mutiprotocol, not using zboss network.
Actually, It is the same situation as...
Hello,
I am in the process trying to send multiple packets over ble but cannot seems to figure out this UART example.
I have read many posts that use ` ble_nus_string_send...
My understanding is that the nRF52840, which is the only nordic device to support the long range bluetooth physical layer. Additionally this chip requires SoftDevices 140...
Good day,
We are planning in developing our own custom-made nRF52840 PCB using the reference schematics provided by Nordic Semiconductor.
In the initial phase of our...
