Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
I am now using nrf52832 sdk14.2 development, as a slave device, I want to set the slave's Bluetooth interval is 1S, I set the following parameters: #define MIN_CONN_INTERVAL...
Hello,
I have nRF52832 with custom board and using SDK15 with Keil uVISION 5. I am working on beacon example and I have modified it to show battery level. I have done necessary...
I am using the bootloader_secure_serial example from the SDK 14.0.0 on a 523832 DK. I have erased the device and flashed the softdevice and bootlader on it. The LED1 is turned...
Hey, I would love some guidance on this:
1. I have one NRF52840 advertising constantly at 8dbm, this device is connected to power so it's hard coded to the maximum transfer...
Greetings,
Based on your librairies/examples, I can succesfully write and read data from an external flash (MX25R6435F) using QSPI with DMA.
I'm using a custom board with...
Dear all
I am on the pca10040 board (nrf52832), and I see the "Thingy_bridge" program is pca20020 board, as shown in Figure 1;
I am in the burning process, the simulation...
hi, im using ble_app_uart and im trying to do a simple communication and data transfer over bluetooth with my iOS.i want to send from the Bluefruit app a byte (0x55 for example...
Hello,
I'm using IAR 8.22.1, SDK 15.0.0, S132, nRF Connect V4.19.2.
I've loaded the 'secure_bootloader' example to PCA10040 EVB.
The device is recognized as DFUTARG...
Need to pass data from a battery powered sensor to a PC via a RF link. Would prefer
a COM Port emulation at 115,200 Baud. I already have a pair of nRF52 Development
Kits...
Hi guys,
Going through mesh packet format today and I'm stumbling upon the time_required_to_send_us method in broadcast.c which is used to calculate and indicate how long...
Hi,
I read and tried Mesh DFU given in " DFU quick start guide of nRF5 SDK for Mesh v2.0.1".
It says "To perform DFU transfers over mesh, use a customized version of...
Hi team,
Is there a way to figure out the phone id (to identify the source of pairing) after the phone has paired with the nordic device?
Basically what we need is is...
Hello,
I've downloaded nRF mesh and installed it on my iPhone, I can use it to provision my device, but there is a question about how to import AppKey on it.
I clicked...
