Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I got the following hardfault when running sdk 14.2, nrf52832. Since the address shows it locates in softdevice...I do not know why. May you please give me tip? Thanks...
Hello, we have a handheld device with Microchip (ex. Atmega) Microcontroller that essentially monitors and records different environmental conditions and stores them them...
I am making PUC for sending & receiving string through ble nrf51822 to phone(nordic app) with particular user define time interval like 1 min , 5 min etc. using ble_app_uart...
I'm running \nRF5_SDK_15.0.0_a53641a\examples\ble_peripheral\ble_app_uart\pca10040\s132\arm5_no_packs and following instructions from http://infocenter.nordicsemi.com/index...
Hello,
We are using in nrf51822 in a product.
I do not understand whether by definition and, thus, always, before connecting, whether a peripheral
goes to sleep between...
Hi,
our device has a hard current limit of 2mA. Normal BLE operation is actually no problem. Connection parameters and packets/event are negotiated accordingly between master...
Hello,
I am using nrf SDK 15.0.0. I am unable to build ble_app_uart example in SES. It shows this error in the screenshot:
But i can build the same example using Keil...
Hi everyone,
I want to set LF CLK source to XTAL without softdevice. But, LFCLKSTAT value is 0x00010000(CKL RUN, CLK SRC = RC) after clock start.
So, I checked same test...
When drawing lines of equal start and end x, y coordinates the GFX library shall draw a rectangle with thickness applied. If the value of the opposing axis has a start value...
Hi everyone,
This might seem like a silly post, but this happened.
I build and ran the example QSPI code given in the sdk.
But after that if i try to run my own code...
We're writing code that does dynamic pin assignment which may change over time. This question is about how the crossbar deals with conflicting pin settings.
If I set the...
Hi Technical Team,
nRF52832DK is running on central role with the below
SDK version : 12.3 IDE :IAR
It is working (connection,just work pairing,bonding, & reading/writing...
Hi,
I have connected the components mentioned in the reference schematic from the official website to my nrf52832 chip. Is there any easy method to know whether it is working...
Hello Im preparing a device that uses nRF51422 for CE and FCC testing. I need to disconnect the antenna and put a connector in it's place for the testing. I have doubts about...
