hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
this packet is capture by wireshark .I use nrf51822 and sdk12.3 connect Balance car,but the packet not have LL_VERSION_IND, LL_FEATRUE_REQ、and LL_Connect_UPDATA_REQ these...
Dear Nordic Team,
Thanks for supporting.
now i am workwith secure dfu. I followed this link https://devzone.nordicsemi.com/b/blog/posts/getting-started-with-nordics-secure...
hello
I am just starting to use the nrf52832 .
I design the PCB with nrf52832 and want to load the softdevice.The nrf go studio can not detect the nrf52832, but the keil...
I was facing some issues getting PWM peripheral work on my custom nRF52840 board. And then I tried the pwm output on P0.08 instead of P0.06 and the signal came out just fine...
We're developing a new device for a regulated market (medical). As such, we need to have control on what third-party software we're using, and how it is working. While starting...
I wanna implement this code for the app inventor, but there was several problem here. I can't use array or index for developing my trapezoidal method.. like this..
code...
Hi All,
We have build a BLE beacon device based on the nrf52 chip. The device works fine but we would like to get a finer control over the TX power since it is used for...
compiled nRF5_SDK_15.0.0_a53641a\examples\ble_peripheral\ble_app_rscs example but will fail on adding chararteristics in char_add() setup: SEGGER Embedded Studio for ARM Release...
Hi guys,
I am trying to use a TM2001 amplifier ( Taiwan Microelectronics, google returns the PDF) to amplify the signal from an nRF24L01P.
The TM2001 seems to accept a...
Hi.
I want to create Bluetooth mesh network and I need that each of device at first must be provisionee, but if in a minute it hasn't been added in a network by provisioner...
Hi
I was designing a custom board for nrf52832. The 32MHZ crsytal mentioned in the refrence design of nrf52832 is not available on digi key. So I am ordering the below given...
Hello,
I have a string data and I want to get a part of it which start for example with "hello" and I want to get 20 characters after "hello".
(for more details I'm using...
in the demo of EnOcean switch translator client,there is just enocean_switch_nrf52832_xxAA_s132_6_0_0.emProject .is it use the same demo as client in the example of light...
Hi, I am using nrf SDK for mesh and try to add FreeRTOS , but after adding build failed because both has files with same name. Is it possible to work with FreeRTOS and nrf...
