Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
HI
SDK-15 - NRF52840
I'm using SAADC example of the SDK.
I read the ADC values and I make an matrix to calculate FFT using the CMSIS library..
the problem is when...
I'm definitely not the first person to ask about this, and I probably won't be the last.
Am I being exceptionally dense, or is the nordic SDK exploded across dozens of folders...
I'm using a nRF51822 on a PCB to connect with a mobile phone. I would like to know whether there is an existing example or library available to work as a central device and...
I am using BLE for NUS template example to create my app , and when I Compile my code with Keil 5.23.0.0 with optimization Level 0, It behaves good with the following operations...
Hi,
I'm developing an app which requires continuous advertising. I use following ble_gap_adv_params_t:
ble_gap_adv_params_t adv_params;
memset(&adv_params, 0, sizeof...
I need to operate sdcard from pc(by usb msc) and from mcu (nordic 52840) (fat32 filesystem) spi sdcard at same time ;
so i have a problem ,when i operate the sd from pc...
Hi,
I seem to be able to read over UART but not write. I have my nrf51822 ( https://www.waveshare.com/wiki/Core51822 ) setup to a pro micro (3.3v, 8mhz). I am confident...
Hi,
I have a multiprotocol application and I'd like to do BLE scanning for as long as it's possible. For now I made 30% to 70% BLE to Thread, and it's the most I can give...
Hi,
I'd like to be able to use an event from the LPCOMP to sample the RTC (either to a peripheral's register, or to a memory address), so I can measure pulse widths without...
Hi there!
I am running the Thread Border Router example and have successfully loaded RaspPi_OT_Border_Router_Demo_v1.0.0-1.alpha.img into the RaspberryPi 3B+.
The problem...
Hi,
I've modified light switch client to read input from GPIO pins . I used int_pin_change as a reference for initializing inputs. The Int_change_pin example uses interrupts...
Hello, I'm developing an debugging an BLE application. I'm using nRF Sniffer (dongle) N51422 PCA10031. I can successfully sniff and decrypt ble secured connections of my application...
