Hello all,
According to the documentation and this feedback on a case there is a maximum size for a particular cert before nrf_inbuilt_key_write returns NRF_ENOBUFS . Can...
Hello,
I am using nrf52840 DK, Segger Studio IDE, Win10.
My application is I want to transfer the image from iOS to the DK board.
I am aware of the Image Transfer...
Hello, i intsalled the software stack for use with latest release of nrf sniffer package.
By starting the capture process with wireshark 3.2 i have noticed an issue:
In...
I have a project where we have 2 nrf51 that need to be time synced with eachother.
The problem is they are placed on the body one on the back and one on the chest of a person...
on the page
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_nrf5_v16.0.0%2Flib_crypto_backend_micro_ecc.html&anchor=lib_crypto_backend_micro_ecc_install
step...
Hi,
In our one of the product we are using Nordic nRF52840 MCU and we compiling this application code in windows with SEGGER Embedded STUDIO IDE Version 4.30a and Tool chain...
Hi guys,
I just wished to quickly clarify the ordering of notification/indication behaviour on SoftDevice S132/140.
If I were to post a notification then immediately...
Hi,
I was trying to get SAADC readings from AIN0 to AIN7 and also from VDD but I'm getting strange results. There is nothing connected to the pins but the measured value...
Recently I have encountered a software hanging issue on one of our products. It was based on nRF52840, with FreeRTOS (Thread SDK v1.0). The issue was apparently related to...
My application needs to keep time and support local time as well. I have implemented a service that allows setting the epoch seconds as well as a local timezone string. With...
Hello, I have an issue with the init packet on SDK13.1. i used nrfutil to generate the .dat and .bin files that i read with Hex editor to transform then into byte arrays....
We've purchased the nRF6700 (nRFGO Starter Kit) and nRF24LE1-F16Q24-DK (Dev Kit) from Mouser Australia.
Both products arrived without Product Keys - so can't download any...
Hi all,
I am using the S332 softdevice for dual ANT/BLE stack in SDK v14.2 bundled with bootloader_secure_ble, which was apparently power optimized in SDK v15.0.0 (see my...
I have made a custom board based on the raytac NRF52840 module (MDBT50). When i load in the USBD CDC example (SDK version: 15.2), The device is not detected. There is no output...
Hi, I would like to build a mesh network with ANT so I tested the ANT scan and Forward example for nRF52832. And the current consumption is around 5mA, is this current normal...
As in the title, I installed 64bit nRFgostudio, however it crashes just after opening with the log below. It opens fine when I do not have my Thunderbolt 3 docking station...
Hi,
How can I send message from servers other than 0x105 and 0x106 to client?
I receive status message in client from servers 0x105 and 0x106.
I can send message to...
I'm trying to use the SDK 15.0 saadc example with a potentiometer on AIN0, and I'm getting weird values. Left pot pin connected to VDD, right pot pin to GND, center pin to...
Hi Nordic:
I want to add some rtt log in the bootloader code, so I make bootloader flash start at 0x77000, size is 0x7000, and my application's FLASH_PH_SIZE is 0x77000...
Hello, I read in the documentation how to create a model, in the client model, which defines a struct: simple_on_off_msg_set_t {uint8_t on_off, uint8_t tid}. I do not understand...
See: http://www.keil.com/forum/63929/
Everything here refers to J-Link, eg devzone.nordicsemi.com/.../a-working-demo-of-monitor-mode-debug-mmd-on-sdk-15-please
and Google...
