Custom PCB with nrf5340/nrf7002. Currently was using NCS2.9.0, with WPA2-PSK connection to the wifi.
While trying to enable use of WPA2-Enterprise, I updated to NCS3.0.0...
When using the shell_module project of SDK v3.0.1, I changed uart20 to pins p2.0 and p2.2, and the serial port printed garbled text.
Below is my overlay file:
Strangely...
Beginner here .. steep learning curve for Nordic ... trying a project with I2S. Took half and hour with an ESP32, but many many hours later, no joy with Nordic.
Working...
Hello. I use the function zb_zcl_finish_and_send_packet to send data from ZC to ZED and it works but one problem is that we're using a rather slow poll (20 seconds) to enhance...
Dear Nordic DevZone,
I'm encountering pairing issues with mobile devices and a nRF54 DevKit flashed with HCI over UART firmware. After initial pairing, deleting the bonding...
Hi, i have locked my beacon with the write_lock characteristic and now i want to unlock the beacon with the lock code which is hard coded in my code. but i was unable to do...
I'm using the nRF9160 with the LIS2DH accelerometer and SDK version 2.5.2 . In my hardware setup, INT1 is connected to GPIO 0 and INT2 to GPIO 1 . I'm configuring both interrupt...
Hello,
I am currently using the `AT%XICCID` to obtain the ICCID of Hologram eSIMs. The output of some of these eSIMs are just the raw 20 digit ICCID with no ending checksum...
Hi,
I’m looking for your recommendations on a suitable conformal coating for an application subject to high humidity. The goal is to mitigate any potential risk of short...
Hi I am trying to get an SD card hooked up to my nrf52840 devkit. I am using nRF Connect v2.6.1 and I was trying to get the sample code working, so I used the sample in ncs...
I have downloaded nRF connect setup V5.1.0 and nRF command line tools V10.24.2.
downloaded nRF connect extension , SDK pack and tool chain in VS code.
I added the build...
in this example:
https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/bluetooth/conn_time_sync/README.html
the peripheral has this assert statement when...
Our design has an nRF5340 with RV3028C7 to provide the 32 kHz clock via P0.00.
If I configure P0.00 as a digital input, I can see the pin toggling.
However, if I use the...
Hi
Is it possible and what is the correct way to implement main clock trimming at runtime? Which NCS version this works on?
I see there is already some setup going on...
Hi,
I want to write data to a specific memory. I understand there is ZMS.
https://docs.nordicsemi.com/bundle/ncs-latest/page/zephyr/samples/subsys/fs/zms/README.html#zms...
Hi,
I am trying to build memfault sample as in intermediate course, after hello_world project configuration and prj.conf options addition, i get following build error...
Setup: NCS v2.8.0 nRF52840
Hi,
I would like to ask about the implementation of Zephyr's SAADC driver (` adc_nrfx_saadc.c `).
In the project I'm working on, I need to...
Hello everyone,
I have an nRF5340 microcontroller (NORA B106 module), and I want to connect a square wave signal to one of its pins to read its frequency or count the number...
Dear Nordic:
I used V2.8.0 SDK to build light bulb, and I have commissioned bulb A(node id: 11) and bulb B (node id: 11) successfully!
Then I used below command to add...
Hi,Team,
I'm using the nrf54l15-dk to develop zms to save custom configurations without affecting the pairing information of ble.
So I have a few questions: 1.Is the storage_partition...
I am trying to set up FOTA support with external flash for mcuboot secondary partition. I have gone through several tickets on the subject, but haven't been able to solve...
