Hi,the Nordic team
I am developing Matter over Thread on nrf54l15, this device is a SED battery powered device, how can I measure the remaining battery power?
Dear Technical Support Team,
I am trying to integrate and run TensorFlow Lite Micro on the nRF5340 Development Kit using the nRF Connect SDK. I have tested both SDK version...
Hi,
I am working with the NRF52832 SoC using the NRF52 DK and developing with NRF Connect SDK version 2.7.0. I have enabled BLE with LBS, BAS, and FUOTA services, along...
Hi,
I am trying to port the DTM example to our board, 52833 based but when DTM is initialised I get about 1400ms of CW then:
00> *** Booting nRF Connect SDK v2.5.2 **...
Hi Nordic team,
We are planning to use the STM32H747 as the host MCU to control the nRF7002 for Wi-Fi functionality. Based on reference materials and existing use cases...
Hello Nordic team,
I am working with the nRF54H20 and would like to integrate both Enhanced ShockBurst (ESB PTX) and Bluetooth Low Energy (BLE peripheral) protocols in my...
Hello, checking if I'm doing this right of restoring initial fw for 91X to work with Quick Start v1.2.0. as described here in Get Started, https://www.nordicsemi.com/Products...
Hi,
I tried to build your own example about "fatfs" on my board "nrf52840pdk" ( with MyNewt as OS ) but it seems that "ff.h" can't be found. Has it got any dependencies...
An nRF5 SDK for Mesh v2.2.0 dimming example client running on a nRF52840 Preview DK is not detected for provisioning by a nRF Mesh smartphone provisioner.
Running the example...
I am in process of doing my eng. thesis and apart from setting up Thread network part of my work is to measure delivery time of messages.
For now I have an application based...
Hello!
I am using NRF51822 in receiver mode with enabled interrupt on ADDRESS event, and even if transmitter is switched off I still get a few messages every second. It...
hi........
i have customized one program ....using segger 15.2 ...nrf52832
when degug it,the code from button and leds stops at nrf_breakpoint_cond ... even it doesn't...
When performing pre-qualifying Bluetooth radiotest of our hardware (utilizing the nRF52840-chip) at NEMCO, we experienced very strange behavior. The frequencies detected in...
My setup of the buttonless BLE DFU secure bootloader using SDK15.2 isn't launching the application after a successful OTA package transfer. Using RTT and breakpoints, I narrowed...
Hi ..
I am using nrf52832 and peripheral device sensor ..segger 15.0
Is it possible to wake up from sleep by interrupting the sensor .. possibility is there ??
Hi,
I am shifting my program from version 11 to 15.2. While including SPI files to the ble_app_uart code, I met with this issue. I have enabled all defines for SPI interfacing...
I'm trying to get the ble_app_uart example working on a nRF52810. I'm using SDK 15.2.0 together with Softdevice S112.
The infocenter says the Example needs Softdevice S132...
I'm facing the issue, that the app_ble_uart example just works if I hook up TX/RX of my USB - UART converter. Is this a desired behaviour? It doesn't seem to start and advertise...
Hello Nordic team
I am working on nRF52832 DK with SDkv15.2. Example code ble_app_buttonless_dfu.
I have created successfully bootloader and zip file to update the firmware...
Hi Sir/ Miss:
I use master emulator to develop software testing device that dll version is 2.1.13.14.
It's developed on using C#.
And, I use nrf51 dongle (PCA10031...