Hello,
We have the custom board with nRF54H20. The VDD_EXT pin is used to power some GPIO ports of nRF54H20 (P1/P2/P7).
The voltage we see on VDD_EXT is about 1.3V instead...
Hi,
I want to test the behavior of Enhanced Multi-Admin added in Matter 1.4.
Is it possible to verify this behavior using a Nordic DK board, sample code and a Raspberrypi...
I've been able to flash consistently but I finally got my nrf5340 custom board working using Hight Voltage DC/DC by setting it to UICR_VREGHVOUT_VREGHVOUT_3V0, but when I...
Hi,
I had a working project for nrf Connect NCS 3.0. I don't know what happened, but now I can't even create a new build configuration. Every time I click on "add build...
Hello,
Please forgive me for this question. I am an extreme noob. And am trying to get started with my first project.
I am working with the nRF52840 DK, and I am trying...
Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hi,
SDK:nRF5_SDK_15.0.0_a53641a
Chip:nRF52810
Example BLE:ble_app_uart(pca10040e \ s112)
Example 2.4G:esb_prx(pca10040)
I am working on BLE and 2.4G integration...
Hi,
I use SDK is :nRF5_SDK_15.0.0_a53641a
But the SDK version in the link seems to be lower
devzone.nordicsemi.com/.../setting-up-the-timeslot-api
I am going to step...
I'm developing an application to communicate with a smartphone. I have the need of writing characteristics with the size bigger than the negotiated MTU, so I'm exploring Queued...
Hi guys, our team now are trying to used nrf52832 to stream audio to ios app, and as you know we are in trouble.
Here are some info about our test env:
1. mobile app...
Hi everyone,
I wanted to add a second UART (UARTE1) to the CLI example in the OpenThread SDK 0.10.0 since UART0 is used by CLI but I was not able to find any documentation...
Hi,
Can't get rid of compilation error about undefined NRFX_SPI0_INST_IDX after adding nrfx_spi driver. Searched the forums and found similar issues but none of the suggested...
Sir,
Did you succesfully compile the NRF5 mesh on SEGGER STUDIO ? I did try with updated segger but i am getting the same error!
And i cant see too the sdk_config.h to...
Hi,
I just received nRF52-DK recently.
I am using Ubuntu 16.04 (64-bits) OS.
I installed JLink_Linux_V620b_x86_64.deb and was using nRF5x-Command-Line-Tools_9_6_0_Linux...
Hi, I am developing an SPIS interface on the nRF51822 using SDK v12.3.
I have configured my device for EasyDMA and I expected to see a continuous stream of data being transmitted...
Hi.
I applied https://github.com/crfosse/Thingy-52-to-nRF52xx project to get thing'y motion sensor by nRF52840 DK.
When I init DK, it discovered only 7 UUID so euler,...
Hi Everyone
I am trying to use BME which is an i2c/twi sensor and EPaper which is an SPI based module. In my code i am using TWI INSTANCE ID 0 AND SPI INSTANCE ID 0.
I...
Hi all:
I am developing the driver of ST LIS3DH and its mcu is NRF52.
If I want to read the value of whoami.
I am not sure if I need call the function of
nrf_drv_twi_tx...
Hi everyone. I'm starting from scratch and using as reference the example/ble_peripheral/ble_app_template.
I'm using Embedded Studio 3.50 + Jlink V6.32 / The chip is nRF52832...
Hi,
I am running the BLE app uart example, using Segger Embedded Studio in Windows.
I've found that that after build and run procedure, the firmware doesn't run, as there...