Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hello,
I'm using the "ble_app_uart" example without a problem. I need to add a timer to this example. For this purpose, I copied the content of the " peripheral_timer" example...
Hi,
I’m working on a project where I need to control a device via BLE_Uart. The scenario I’m trying to achieve is: - I have a network of several centrals und several peripherals...
Hi, I'm trying to use Atomic FIFO in my application, where multiple interrupts of different priorities are trying to read from and write to same FIFO. I couldn't find any...
Hi,
The questions:
When is PB-GATT expected to land in the SDK for Mesh?
What are the best Andorid/iOS example apps to act as provisioner and network...
nRF Connect suddenly can not find the COM port to my nRF Dongle. The same setup used to work fine untill today. I reinstalled the nRF Connect, JLink drivers but it is still...
Hi,
I'm using SDK 15.0.0; nrf52840 DK; IAR(EWARM).
I want to add TWI(i2c) from example in SDK to my project.
But I facing with next errors:
Error[Li005]: no definition...
Hi dear engineers,
I have a strange TWI problem on my production protype which programmed based on the official twi example with softdevice s130_nrf51_2.0.1 and SDK 12.3...
Hi,
I'm trying to schedule few events within the shortest connection interval . Is it possible to shcedule 3 events, 2.5 ms long within 7.5 ms connection interval? Could...
Dear all,
I am using the nRF51822 custom developed board. Earlier it was working fine, but now when I try to connect the BLE with nRF ToolBox APP UART service, the APP...
Hi,
Have flashed an early sd_power_system_off first line in main() when measuring power-consumption...
Now the SWD access seems gone. Is there a trick to get it back in...
Hi, I'm working on a custom board with a nRF52840.
I want to use REG0 and REG1 as mentionned in Figure 13 of the datasheet : with VDDH, and both DCDC. My PCB is powered...
Hi there
I have a NRF52 Dk already and it had been setted as master.
The log might contain the specific advertisement channel power or how much packets has been sent...
Hello,
I want to send 6 bytes of data over BLE. I will set a timer for this purpose. When there is timer interrupt, the data will be send.
What I wanted to ask is that...
