Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Hi!
I want to start scan in central mode after one connect has established and I received success evt PM_EVT_CONN_SEC_SUCCEEDED:
In a SDK13 I can make same, but at SDK15...
Hello!
On the firmware for a certain product, we are using the scheduler module to manage the access to the peripherals (SPI, TWI, Timer, ...), and have also enabled its...
I implemented manufacturer specific advertising to transmit important data without having to connect to the ble peripheral. These data can change over time so I need to be...
I measured the power consumption on NRF52840 DK with project peripheral blinky (SDK15.0.0). The average current is 704uA and the base current is 680uA when connecting to another...
I have a test suite connecting to a nRF52832dk using RTT. This one test writes random data to the UICR config area, resets the chip, then reads back the config.
When running...
Hell ,
I am planing to use nRF52810 for one of my mesh application,now query is
How much power consumption its will take when RF is disable and listening only external...
I am about to buy 5 pcs of nRF52840 DK Development kit for nRF52840 SoC to use for Long Range. How can I ensure the development kits are mounted with chip revision C or later...
Hi Team,
I have read in nordic documents that BLE 5.0 will have 1.4 Mbps of through put.
But when i am testing the through put example with my nrf52832 board, i am only...
Hello. I'm using the example of the light_switch_server project. I need to configure a server (light bulb) driven by 3 clients (buttons), how can I do? I tried this way, but...
Hello Nordic,
I have to transmit data from the nRF Chip(now i'm testing nRF52832 DK Board) to a PC on UART serial.
Each beacon has transmitted advertising and scanRSP...
Based on the nRF24L01P Product Specification 1.0, after 24L01+ enters into Standby-II state, the only 2 ways to leave this state are 1, set PWR_UP to 0, 2; 2, Feed data into...
I've picked up the DK after a break. Installed the toolchain on my new laptop and was ready to throw the 'blinky' example from the SDK on to it to get started. It did not...
Hi Nordic experts:
I use a device with thingy52-provision-demo firmware(from git-playground), and another device with serial-example to provision the thingy-provision-demo...
