Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
I am trying to program mpu_simple https://github.com/Martinsbl/nrf5-mpu-examples with Segger, and I get to connect sensor MPU6050 to my board but I do not receive datas of...
Hello. I followed all the steps provided in the readme document. After dragging and dropping the hex file to the j link, the led 1 starts to blink, indicating that the board...
With an nRF52, is it possible to wait longer to measure the RSSI on a channel? I'd like to measure the RSSI over 1msec or so, rather than a tiny 8us (typical) snapshot.
Hi,
This is my first time to use Nordic product and I have used nRF52832 based SDK 12.0 and SoftDevice132 v2.0 about 2 months. And the IDE used for devlopment is KEIL MDK...
Hi
Im using the DFU secure example (examples\dfu\bootloader_secure\pca10028)
Im working on a NRF51822-QFAA ,S130 SDK12.3 , Im not sure about my IROM/IRAM definitions,...
Hi Nordic Team, One of our customer wants to integrate communication via Thread BLE on his IoT-Gateway. We found your nRF52840 Dongle. Does this dongle have any certifications...
Hi,
I am planning on using nrf52832 for a beacon application. I happen to get a schematic and layout from Nordic website for development.
I am attaching the schematic...
Hi, I am trying to interface MPU^)%) sensor with NRF52832. with help of BLE UART. i will get the resultant data on BLE APP. but here i got some error is this the linking error...
Hi,
we want to made the device which should working in the mesh network without provisiong procedure by user.
Typical application - network with 500 nodes, every node...
Hi, I am using nordic nrf52832 module with BLE mesh SDK V2.2.0 I want to do DFU for application + softdevice without any serial connection through mobile app between BLE mesh...
I got the fail result of the test CPS/SEN/SPE/BI-05-C [Cycling Power Control Point Procedure Timeout].
At this test, the tester does not send the confirmation until ATT...
Hi Team Nordic,
According to the AM2302 (DHT22) datasheet, the data pin will be pulled to high state in idle state. But in my case, when i am reading the data pin before...
I'm developing nFR52832 to communicate with the PC via UART. commands are sent to the nRF and for each command nRF responds with some data back to the PC via UART.
The UART...
