I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
I'm finding my PCA10056 nRF52840 Q1AAAA development kit to be acting very strangely.
1) I takes almost 3x as long to program as a PCA10040
2) Generally I have to program...
I'm using nRF24L01+ since some time, the version on board with LNA end PA with very good results. The electronic is shielded on that module.
Very rarely it happens that...
Hi,
here is the situation:
Compiler: VS 2017
CMake: 3.12
boost: 1.67.0
pc-ble-driver branch: master
Firstly I can successfully build the pc-ble-driver, with this...
So I came from the arduino world and made my life simple by making a resitor bridge with buttons so that I could spare many pins for other features. I have problems finding...
I'm trying to understand which part of the code provides the bluetooth connection between two nRF52840. I worked in sdk15.0.0 with multilink, blinky and uart examples to solve...
Hi, everyone,
We are developing project with nRF52832 chip.
For making it's monitoring we used UART communication port. But on the next step of development we had to enable...
I need to interface an nRF52832 with ADS7042, hence the following questions:
1) as ADS7042 requires 14 clock cycles per read cycle, is the nRF52832 SPI API applicable in...
I am constantly receiving an NRF_FAULT_ID_SD_ASSERT error within a non-deterministic time after connecting via BLE.
The program Counter is always 75936 and Info == 0. I...
Hi
Development Environment : windows 7- keil ARM SDK 5 - Arm Debugger Programmer(Waveshare) - nRF51822 EVK from Waveshare
What is the boot_PIN or Boot_Mode PIN
I want...
I am wanting to increase the length of one of my characteristics used when my device is acting as a peripheral. When I increase the size of my characteristic, the softdevice...
Hi,
I needed some figure for my controller selection,
Please if can you tell tthe exact answer it will be very help full,
Using NRF serial example for uart with baud...
Hello,
I have a voltage divider/thermistor circuit where R1 is an NTC thermistor of 100kOhm at 25 ° C. R2 is 100kOhm right now.
I took peripheral_saadc example for SDK15...
Hi all,
I'm testing out and adapting the Thingy Mesh Demo v0.1 , which uses nRF SDK for Mesh v1.0.1 for my internship. I will be testing out a Thingy's Mesh network for...
Hi,
I tried, ble_blinky example on DK, it works well. Also advertising interval 40ms on nrfconnect mobile app,this is consistent with SDK.
Now, i try same example with...
