I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
hi
I want to design Nodes for asset tracking. These Nodes will be spread out in a building. A moving object will have a BLE -Advertosor. The Nodes will detect Moving object...
Hello, I'm using the nRF51822_QFAA chip on a pca20006 board. I downloaded sample code from the offical site. Installed sample code nRF51822_beacon_firmware_1.1.1.msi. I use...
SDK: 14.2
64-bit Segger Studio 3.34b
PCA10040 Rev. 1.2.4.
64bit Windows 10
SD: S332
I'm trying to add the bpwr Tx profile to the ble_ant_app_hrm_pca10040_S332...
Hello fellows,
I did my master's thesis with the nrf51 and now some years later I need some help setting up a Laird BL652 to work with my beloved NRF+Keil tools.
Here...
I have a Nordic 52832 chip in an integrated module form from Fanstel. I have the NRF 52 DK, the Fanstel evaluation board, and a custom prototype board I built.
I can program...
Hi all,
I have ported my RTOS to nRF52832. It can run app and BLE properly. But when I measure the power consumption, the current is too high when BLE is enabled. Please...
Are the development boards for the 52832 certified for BT5? The 52832 chip is advertised as BT5 but the nRF52DK documentation says it is only BT4.2 compatible.
Thanks!
Hi all,
I'm interested in adding Infineon OPTIGA Trust X to nRF52840, but I can't found enough information.
Is Infineon OPTIGA Trust X hardware-compatible with nRF52840...
Hi,
I have connected STM32 with nrf52832 using STM:TX -> NRF:RX and STM:RX -> NRF:TX.
The communication works fine when i initialize UART on both devices.
The issue...
I am trying to implement a periodic calibration routine that is transparent to upper layers of my application.
I have the SAADC set up to continuously sample one channel...
Hello,
I was able to build the light_switch example using Cmake. But when I tried to build it using segger, I'm getting a board.h missing error. My build path is SDK_ROOT...
Hi! We got the mesh working with our custom model. however if we try to send a package multiple times it throws NRF_ERROR_NO_MEM error. Any ideas why this might happen or...
Hello
SDK12.3, nRF51822
I'm trying to interface the ssd1306 the program freezes in function app_twi_perform internal_transaction_cb is not called internal_transaction_in_progress...
We used nRF5_SDK_15.0.0_a53641a and nrf5_SDK_for_Mesh_v2.0.0_src.
We are following DFU quick start guide http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter...
