I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello, I'm new to Nordic boards.I would like to measure the bit error rate for a BLE link using nRF52840.
Is there any way of modifying any of the existing examples to add...
We use iOS nRF Connect primarily for DFU updates and find a real annoying issue with its behavior. We see this problem behavior on both v1.8.5 and v1.8.2, on both iPhone and...
Dear All,
Brief about the requirement:
ToF (Time of Flight) value computed is inclusive of the overhead delay of notifying to the application layer in the BLE stack...
Is it possible to use app_timer with the mesh stack?
Up to now I was not able to integrate the app_timer library into my build.
Can you give me an example how to integrate...
Hello Everyone,
I'd like to know if it is possible to use nfc to collect bonding informations from a smartphone. Then I'd like to transmit these informations to other devices...
Hi, i'm using nRF52 DK to communicate CX93510 encoder chip via SPI. I'm using nrf_drv_spi library with SPI0 connected to pins:
#define CX93510_MISO_PIN 22 #define CX93510_MOSI_PIN...
Hello all, I'm working with construction like:
To pass some data between APP and BOOTLOADER. At first I tried to place this buffer to the end of RAM, but after restart content...
Hey Hi all, I am new to BLE Technology and it's programming. Well, I need some help on my project that I am working on. I have multiple (=25) peripherals and I want each peripheral...
I've got a custom board using the NRF52810 with SDK v15.0.0.
I am using the TWIM driver (nrfx_twim.c master mode) to drive an LCD driver IC, a capacitive touch sensor IC...
hi , endnode, I has changed app_util.h as this link
https://devzone.nordicsemi.com/f/nordic-q-a/26448/nrf52832-maximum-number-of-central-links/104059#104059
the max link...
Hi,
Is it possible to use variable Read/Write twi data length?
I'm using:
nrf_twi_mngr_transfer_t const i2c_write_raw_transfer[1] = { //NRF_TWI_MNGR_WRITE(I2C_HUMIDITY_SENSOR_ADDR...
I'm looking for someone to hire to make a Thingy program for me.
I'd like to program the Thingy so it picks up ANT+ MO2 data or other ANT+ data from multiple sensors and...
Hello,
I would like to use the bouttonless dfu feature in my application, but I have not been able to run the sdk example ble_app_buttonless_dfu.
The application does...
Hi
I have query on glowing multiple LEDs example 8 LEDS with GPIOs of nrF51422
So went through nRF51822 series based EDK design files and i see they use 4 LEds to which...
