I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I am using BLE mesh SDK V1.0.1. I want to know the answers of following questions,
1. What are the advertising and scanning parameters used for flooding in Mesh?
2. Does...
hey, how can i get on the device pca id which is also printed on the nordic chip on the board.
i use the mesh light on off example and need this id to send beacons with...
The code was already done in another system and it worked successfully.But when I tried to build the same code in my system it shows some error like this "cannot move location...
Hello,
I have brought new PCA10056 board for BLE5 evaluation but hard part is board is not getting detected in nRFgo studio nor in Keil.
I can see COM port getting generated...
As we are building our Mesh stack on the Nordic nRF52840 boards we realized that the fixes applied to mbedOS 5.9.4 would fix some of our problems. Does anyone have experience...
Hi!
SDK:nRF5_SDK_15.0.0_a53641a\examples\ble_peripheral\ble_app_ancs_c\pca10056\s140\arm5_no_packs
Development board:pca10056,V0.9.1.
Because the current process of...
Hi Everyone
Here is what i am trying to achieve with nrf52840 PDK , SDK15.0 And Segger Embedded Stuido
1. I want to create a text file with "HELLO WORLD!" in it.
2....
In the Lower transport layer, segmentation will be carried out. The concept of a place is not very clear. Can you help me?
SeqAuth = IV Index + first segment SEQ = 56bit...
Hi,
I have been trying to implement a Bluetooth keyboard functionality using the nRF52DK. So, from my understanding, what the example program "ble_app_hids_keyboard" present...
I am trying to communicate between peripheral device (nordic nRF52840) with another device (let us say ubuntu device) with ubunutu as OS and Bluez bluetooth stack. I have...
I am trying to implement UART service which should act as both central and peripheral at a time.
So, I started implementing ble_uart peripheral service into the central...
Hi,
I'm testing the nrfutil tool for DFU in windows but it seems that when running nrfutil keys --gen-key private_key.txt I get " no such option: --gen-key" , using nrfutil...
Hello,
I have been developing firmware on a custom nRF51 board.
Upon testing firmware that involved BLE advertising,scanning, UART communication over BLE and FDS, i observed...
hi i have made gate opener for my farm, i am using MPU9250 and nrf52 to measure how much degree its open i am putting my MPU in cycle mode to wake up and take data, but it...
Hello
I would like to point out that I have no knowledge of electronics.
I am in the advanced stages of building a project on the basis of Adafruit feather nRF52832, The...
