After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I have ASUS ZenPad 10 with Android 5.0.2,
BLE device on nRF51, S110 SDK9 with fixed passkey and encrypted characteristics with following settings
#define SEC_PARAM_BOND...
Looking for someone that has previous experience building multi protocol / time slot topologies using a mix of BLE (central+peripheral) & custom Gazell connections running...
Hi.
I have nRF51422 borad and want to flash to nRF51422 with JLink.
I supplied to 3.3V power to board and is connedted SWDIO to p23, SWDCLK to p24. JLink is connected...
IUsing the Master Control Panel application on my Android device to connect to my nRF51822 module (acting as the GATT server), I have implemented the Device Manager (v10 SDK...
I have successfully compiled BLE application using tutorials provided on nordic website.
but when I start doing debugging for better understanding find out that I can not...
Dear all members,
I understand that Secure BLE DFU official support is only for SD132, but I am developing a product for nRF52810 which can only run SD112 and I want to...
This link source.android.com/.../services seems to indicate that L2CAP CoC is available in Android 8.x but support may vary by device vendor. Does anyone know how to verify...
Hi,
I just installed the latest NRF5 SDK - nRF5_SDK_15.0.0
and trying to run examples such as "examples\ble_peripheral\ble_app_hrs\pca10056\ser_s140_spi_5W"
But for...
We are developing a bluetooth product that operates on a battery where every uA counts and I have a couple of questions about current consumption in System On Low Power mode...
I am creating a BLE beacon scanner, using nRF51822 and SDK 12.0.0. My beacons will be using public addresses so the upper 3-bytes of device addresses of all my devises will...
Hi,
in our application we will have a main MCU and a second MCU, an nrf52832.
We need to update the fwon the nfr52832 from the main MCU using a bootloader, via UART. ...
Hello,
I want to use 2 SPI bus with nRF52832 IC and SDK5. I can use the "SPI example" for first SPI bus. For the second SPI Bus, I think that I need to modify "sdk_config...
My devices require calibration and self test to be carried out after programming. To implement this, my device checks the JLink reset pin (configured as a GPIO on my NRF52...
Hi everyone, I'm trying to implement a simple bluetooth beacon which broadcasts / advertises the number of button presses and the time in seconds after the last button press...
Hi everyone,
I'm trying to change the advertisement data while advertising using an interrupt. So far I've managed to use a button to change the advertisement data.
...
Hi,
I have huge BLE carrier frequency drift, which cannot pass FCC requirement.
The drift is 256kHz which seems not normal.
I'm using 32MHz 10ppm xtal so drift should...
Hi!
My setup:
* nRF52 DK
* nRF5_SDK_15.0.0_a53641a
* s132_nrf52_6.0.0
* SES V3.34b 64-bit
In my application I am using Peer Manager to manage bonding and also...
Hi all
The errata sheet V1.8 states that the errata 143 applies also for the Bluetooth Low Energy mode. Does that mean that the BLE stack of the SoftDevice S132 is also...
Hi,
I am using nRF52832 DK and other same custom board, sdk v15.0 with SES IDE. My application like this:
For ble peripheral used example ble_app_uart and for central...
Hi Sir,
In my system (windows 7), I had install the GCC 4 .9 2015 q3 for SDK 14.2.0/12.3.0.
As reference the release note of SDK 15, the GCC upgrade to 6-2017-q2-update...
