Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hi, in my project, the following codes caused "NRF_BREAKPOINT_COND":
sd_power_ram_power_set(4,(POWER_RAM_POWER_S0POWER_On << POWER_RAM_POWER_S0POWER_Pos) | (POWER_RAM_POWER_S1POWER_On...
I have secure DFU working fine for my s132 (SES sdk15.0), and now trying s112 using the example from post how to use dfu?
I used SDK_14.2.0_nRF52810_Secure_BL_v1.1.zip and...
Hi. I have to make mesuring impulses quantity of two external low freq signals without interrupts.
I tried to use GPIOTE EVENTS_IN[0] and 1 with PPI ch 0 and 1 to timer...
I use PCA10040 V0.9.0 to run SDK15 bootloader example: F:\Nordic\nRF5_SDK_15.0.0_a53641a\examples\dfu\secure_bootloader\pca10040_ble_debug\arm5_no_packs.
1. erase full chip...
Hi, I am using the ble_app_cscs_pca10056_s140 example application from nRF5_SDK_15.0.0_a53641a and I have made a single-line change (see below) to force the bonding process...
Hi Nordic Team!
I have bought nRF52 DK and my aim is to create BLE application for a peripheral that it would be possible to connect multiple centrals (for example android...
Hi,
I am trying to add the SAADC to an existing project. SDK 14.2 - Softdevice.
I quickly changed the existing code as follows:
Unfortunately, the callback gets...
Hi.
I am using the nRF52840 DK board and have integrated the SDK15 ESB_Rx example with the HID example.
The nRF52840 DK board has two USB ports. (J2, J3)
J2: Firmware...
Trying to track down an issue with IOS disconnecting shortly after connection when using NRF Connect, LightBlue doesn't connect at all.
We have a few GATT chars with...
Hello,
I am facing an issue when trying to use the example flash_fstorage_example in SDK15 with the softdevice. According to the documentation, using the reading and write...
I am testing SPIS to transmit mass of data(255 bytes each call) from nrf5 DK.
I found SPIS data shifting randomly.
The testing data is 0x88 but sometimes can get 0x44...
Datasheet of the Sensor:
www.ctconline.com/.../1_VS_TA102_DS.pdf
Accelerometer Out = 100mV/g =equivalent to=> +/- 8Vpk-pk
Temperature Out = 10mV/°C
Please provide...
FDS uses softdevice API. SDK 14.0.0
FDS writes are all successful for the same file id and different record keys until the flash is full
fds_delete_record() is called...
Hi,
I'm developing software for the nrf52832. However, I can't use the SDK of Nordic for several reasons.
In the code, I would like to save a small amount of data...
