But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hyvää päivää,
I'm moving from Eclipse to SES which on the face of it seems smoother and cleaner. My problem is figuring out how to setup my projects. If what I want can...
I am integrating app_timer with no softdevice..
Code compiles and runs correctly at the begining but it only executes the timeout_handler function once after the app_timer_start...
I'm using nRF52, nRF52832, PCA10040 with SDK 15.2.0, nRFGo Studio v1.21.2.10. Is it possible to place all 3 of the following separately on the device using the Studio?
...
The nrfutil documentation/application is used to create a .zip file to dfu update. This package may contain a combination of application/bootloader/soft device along with...
I have looked at secure_dfu_test_images\ble\ for nrf52832 and would like to create a blinky_application_s132.zip (corresponding to hrs_application_s132.zip) to do some testing...
Team,
For asset tracking I am using nRF52840 Beacons as tags in asserts and Raspberry Pi B+ for scanning Beacon's MAC, UID, Major, Minor, Tx, and RSSI values.
To calculate...
I want to send data from nRF52840 Dongle to Raspberry Pi B+, Assume nRF52840 Dongle placed in USB drive of Raspberry Pi B+. Please help with coding sample.
The code assumes that check_rollovers_and_update_eid(...) is called every second, and that m_security_slot [slot_no] .timing increases monotonically with 1. If this is not...
Hi
I have tried to run DFU example from SDK 15.0.0_a53641a.
I also use nRF Connect v2.5.0 to update firmware.
I flashed Soft device and secure_bootloader( examples/dfu...
I'm trying to enable the UART module. The function calls follow:
nrf_init -> nrf_drv_uart_init -> nrfx_uart_init
Here we see that nrfx_uart_init() is called with
result...
I suspect I could avoid writing (admittedly, simple) code to map ble service objects to connection handles and vice-versa if I knew how to properly use the BLE Link Context...
Hi, I am merging the Thingy app (Segger with softdevice s132_nrf52_4.0.5) with the UART example (taken from ble_app_uart in SDK 11). I have been fixing some errors before...
Hi All,
I built a custom board that mounts a nrf52840 chip and I followed the schematic N 5 of the datasheet.
I also have 2 evaluation boards nrf52840 EVB "PCA10056",...
Hello,
I am interested to know if the device nRF51824 compliance with the ATEX zone norm (for example, working in certain parts of the chemical industry)
Best regards
Windows7 , nRF5_SDK_15.0.0_a53641a-ble_app_uart,,
Environment setting of SEGGER embedded studio for ARM V 3.34a
I am preparing to develop ble_app_uart using [SEGGER Embedded...
