I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
I am trying to use UART with interrupts and fifo, by using nRF52 SDK 12.2.0 example. It works until the first overflow, after which I cannot any more receive characacters...
Hi!
I'm using an NRF52 with app_uart. As expected at 115200 baud rate, I occasionally get overflow errors which I can see in my event handler.
However, after these errors...
Hi,
Where are scan requests sent? I'm trying to find the function that does this because I would like to disable it.
I only want to connect with a peripheral based...
Hi everyone:
I am using the NUS (nordic UART service) in my project, and find one problem in this project. The development bench is: SDK13.0, nRF52 DK.
If I build a NUS...
Hi,
I used IOT TCP Server example of nRF5 SDK(Ver.15.0) to complete the communication
between the Raspberry Pi and the PCA10040.
But I found that the communication speed...
Hi,
1. I want to disable MCU UART connection which is SB with GPIO pin 5, 6, 7, 8 and I need to connect that pin on arm based processor so desoldering those short bridge...
Hello,
we are facing a weird issue with a few models of smartphone since we increased the max MTU size. We are testing at the office with the Xperia E6553 but the Samsung...
Hi there
I am stuck. My incremental wheel with photocell and comparator circuit does not work if the QDEC hangs on it. But seperately it works fine.
When I hang it to...
Hi Team,
Which models are supported in the latest mesh SDK?
I can see support for the on-off model.
Is Time and Scenes (Explained in Mesh Models.pdf, Section-5, Page...
I use SDK13, nRF52, S132
I use bootloader_secure_ble with generated public key for bootloader and for nrfutil. After all steps like discribed on
devzone.nordicsemi.com...
Hello.
I use nRF52832 and power from 3.3V source. Also I use the accelerometer and gyroscope with VDD 2.5V and 3.0V respectively. They are connected to nRF through SPI....
Can a device that is configured and programmed from Keil (softdevice, application, bootloader) be updated with code that has been compiled on ses (application)? I have converted...
Hi,
Referring to bootloader programming article - there's a post-build phase of programming UICR.BOOTLOADERADDR
The article describe how to use nrfjprog to do this which...
Hello,
I studied the "gpiote" example in the SDK. In order to fully understand how it works, I attempted to modify the "template_project" example and follow the process...
