Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hello, as the title suggests, I have an issue when powering the nRF9151 DK with an external power supply. Normally, I power through USB, and it's fine. However, when I followed...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hlo
I have to asked that i am working with custom board of nrf5340 and i want to flash and check the rf signal by flashing through the nrf5340 development board and i am...
Hi all,
I'm encountering an issue with the TWIM30 interface on the nRF54L15 (pins P0.03 - SDA, and P0.04 - SCL), using vanilla Zephyr v4.2.0-rc1.
The setup involves external...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
Hi,
I'm very new to c programming and your hardware. Please excuse my novice questions.
I'm making a rotary braille display using nRF52840 dongle (PCA10059) as it's brain...
Hi,
I using custom nrf52840 board .I have loaded the Bluetooth program in to the custom board using swdio/swclk/vtg/gnddetect these lines.There is no problem in Bluetooth...
I'm attempting to get MMD set up in an IAR project following this tutorial: https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/monitor-mode-debugging---revolutionize...
Dear sir, We are using BL654PA from Laird technologies. We want to check RSSI at 2402MHz, 2440Mhz, 2480Mhz. Can you guide us how to enable PA without using Nordic stack file...
Hello,
I'm using a Thread Border Router built using a Raspberry Pi 3 and a nRF52840 Dongle. I followed the steps at this link: https://infocenter.nordicsemi.com/index.jsp...
Dear Nordic Semiconductor support team
Hi, I got your support using micro:bit with nrf52832 by RADIO in the past as follows.
https://devzone.nordicsemi.com/f/nordic...
I've noticed that Thingy:91 USB code has some issues related to proper handling attach/detach events resulting in incorrect response to usb host requests. Windows device manager...
Hello,
I am using the this sample;
https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples/samples/nrf9160/udp_gps
I want pvt data instead of nmea data...
Hi,
What is the best way to read the async data received on a UART in to a buffer when ever there is an a byte available and in a separate task read the data from the buffer...
I need to include RTOS support in my NRF52840-based system. In order to obtain a good FreeRTOSConfig.h I've looked at the four examples in NRF5 that include FreeRTOS and,...
Hi,
I'm trying to make connection between nRF52840 dongle programmed with "examples/peripheral/cli" application and Windows 10 UWP "CustomSerialDeviceAccess" example code...
Hello
Currently I use the example "ble_thread_dyn_mtd_coap_cli_pca10056" and I would like that my application can detect timeout of the messages sent on the Thread network...
Hello, First of all, I hope you are doing okay about the corona virus crisis. I wish that you stay healthy and safe . Recently, I have been trying to configure ble_app_uart...
Hi Sir,
In the datasheet (V1.1), the table-145 shows the dimensions of WLCSP, but there is no tolerance of D/E/D2/E2
Could you help to advice what is the tolerance of...
I have a project where I am implementing an alternative logging backend. My design is modular so there could be multiple logging backends. Each backend is initialized with...
