I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
I have a project that needs to scan and filter the advertising name, uuid and mac address from the device. I will set them one by one and enable them one by one. I set them...
My problem seems to be a lot like case numbers 217967 and 243215.
I do not have an oscilloscope or logic analyzer.
I am using a nRF52840 DK (PCA10056 1.0.0 2018-17) and...
I've just received my nRF9160 development kit this morning and after trying to setup the development environment for a few hours I've come to a halt.
I got it working...
I am looking to use libuarte in our project. We are creating a battery powered device and so need to be low powered. EasyDMA draws about 1mA when running which is far too...
Hello,
We are developing an application that is trying to receive a steady stream of bytes from a serial port. But we constantly get a fatal error when we call app_uart_get...
I'm running 6 X Thingy:91s in pre-production for use as a GPS tracking/iOT solution. Currently I'm located in Austin, TX. If I do not request GPS, I receive regular data from...
Hi all, I'm working with NRF52DK using Segger Embedded Studio with NRF SDK 15.0 trying to communicate to a UART sensor using the serial port abstraction layer API. Following...
Hi all, I'm facing an issue communicating with a UART-based sensor on the NRF52DK (52832). I've followed the serial_port example and using various forum topics I've got to...
Hello,
I am using the nrf52832 bootloader and i got it working with the s112 sofdevice and a custom application mapped at the end of the softdevice.
I want to add another...
Hi guys the following is an Arduino code:
In here,
We are taking the rising edge pulse to measure the rotation per minute of the DC motor and to detect whether the DC...
Dear Community,
I am trying to implement a simple Tensorflow Lite C++ project on the nRF52833 board. I work with the Segger Embedded Studio.
Therefore I added the tensorflow...
Hi,
I have extended the nRF9160 sample app to use Leshan bootstrap server. Using a boostrap server means getting DTLS PSK crypto keys from the bootstrap server. Hence the...
Hi,
We are testing Buttonless Secure DFU without bonds using the windows nRF Connect app. If I open the "Secure DFU" service in our app, enable notification for "Buttonless...
Hi everyone!
I was not able to find the answer, so could you please clarify what did I miss when I exercised with my application.
First, I was able to build ble_central_and_peripheral...
