Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
To the kind attention of Nordic support team,
I'm evaluating your standard gzp example (proprietary_rf/gzll/gzp_dynamic_pairing, sdk15.3). From what I see, the device to...
Hi,
It seems that the nRF52811 for the most part draws less current the nRF52832. For example:
nRF52811: 1.4 μA at 3 V in System ON mode, no RAM retention, wake on RTC...
Hello,
I cannot reset the nRF52 DK while running on battery power. I've tried multiple examples of the SDK which didn't work. However, when connecting the DK via USB, the...
I don't know if I'm dealing with a hardware or software problem at this point. I have a custom NRF52810 board with chip antenna and no LF clock, in SES. In SDK 16 I modified...
I'm running the esb_ptx_pca10040e on a custom board with NRF52810. The program gets stuck on....
while (NRF_CLOCK->EVENTS_HFCLKSTARTED == 0);
This appears to be similar...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
1) Previously we had a custom board...
Hi,
I was testing the various cases for DFU & I was looking for any possible solutions to fix the issue.
I flashed SD + bootloader (secure) + app from SDK 15.2 on the...
Hello,
I´m trying to update the certificate of my nRF9160-DK. To do this the modem has to be in offline state. I´m running the AT Client sample like it is shown in the chapter...
I am curious if there is an inherit maximum transmit duty cycle of either M1 or the nRF9160. I am asking for this because we need these numbers for SAR test. Our product will...
Hi All,
I am working on a project with NRF52840 , we are looking for a solution to do the OTA to device by the central device , both of them are using NRF52840 as BLE module...
Hi, I need to be able to count the number of packet Tx and Rx from one board to another in order to compute a packet loss ratio for certification purpose. To achieve this...
hi all:
Use PPI+timer+adc, in the following ways:
called stop, then unable to start adc, Couldn't get into the NRF_DRV_SAADC_EVT_DONE.
Could you tell me how?
Hi,
My product is undergoing susceptibility test and strange issue is happening after the test for 1-2 hours, ie while trying to send data with higher MTU size notification...
