Hello,
We struggle to keep LTE-M attached with nRF91 (Modem) and CMW500 (EPS) to test regular IP communication (so those are not Radio Access Network tests) during product...
Hi everyone,
Could someone help me with the following use case?
Task description: I'm working on a firmware update procedure based on the smp_svr project. I'm trying to...
Hello,
I have made a project that was based on the nRF9151 Development Kit and it works great. I had to select the -ns configuration to get anything to ever build and now...
Hi,
I bought a new nrf52840 DK board as one ofthe original nrf board of my Qorvo QM33120WDK1 kit ( 2 x nrf52840 DK + QM33120W + QM33110W) J3 connector broke. Out of the...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
I am trying to set up UART communication between the nRF9160 and nRF52840 that are found in the Fanstel BLG840XE. Currently I am sending a test string of "abcd" from the nRF52840...
Hello,
I am trying to build a remote control using NRF52832 SoC, SDK16.0.0 with softdevice S132 version 7, Keil 5.
I have to control a servo motor and i want to achieve...
Hello,
I need to send logged sensor data in external 4MB flash to a phone via BLE.
I am using a nRF52840 based module on a custom PCB. I am using SDK v14.2.
I am using...
Hello,
Is it possible to get access to the information contained on the SIB (System Information Block) in the nrf9160? if yes, is it through the nRF Connect v3.3.0?
Thanks...
I want to get the 128 characteristic UUID of the peer device during the connection phase. Now I use SDK is 15.3, the softdevice is 6.1, and only 16-bit UUIDs are obtained...
I have the NRF52 DK, I run make flash in the UART example, everything works. I'm able to run the loopback test.
I navigate to the serial port example, make flash, nothing...
Hi Everyone,
I would like to understand how the multi peripheral application works in this given scenario:
Scenario:
Considering one peripheral (P) is connected to 4...
Hello,
I have been working with NRF 52840 DK and finally able to make the advertising work on PHY CODED but I was required to use extended packets.
My question is
Is...
Hi i am using sdk15.3 secure boot-loader example. i had change backend to cc310. without optimization i am able to upgrade code but when i am using optimization level 0 it...
Hi,
I am working on an USB CDC program with nrf52840-mdk-usb-dongle. The PC needs to use a terminal emulator like putty to connect to the dongle. Now I send and recieve...
I use Zigbee CLI example on nRF52840. (examples\zigbee\experimental\cli\cli_agent_router)
It use UART as 115200 bps with CTS/RTS (hardware flow control).
I want to change...
Our product uses non-connectable/undirected advertising, where advertisement packets are sent every 1 minute for 500ms time. For that we are using FreeRTOS timers to start...
1: Is there any information that can be systematically introduced to the production test of Bluetooth products? 2: What parameters do I need to test for mass production of...
Apparently， Config AppKey Update message can be transmitted in the key refresh procedure. However, one point let me very confused, I looked into the Mesh Spec v1.0.1 (page...
Hello. Is it possible for a central device to retrieve the BDADDR( 6 byte array data ) of a past peripheral device by using the peer manager? ("past peripheral device" refers...
