Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hello,
I'm trying to add a third characteristic to my BLE service and when I add it, my device "fatally" crashes in Release mode with no meaningful error information ...
Hi I'm having trouble updating the firmware on a custom board using JTAG through the NRF9160 DK.
I've attached the log file from the programmer of the error I'm getting...
I loaded up the zephyr sample blinky example, compiled ok, and went to download to the nrf5340-pdk...
I got the following error dialog plus some more misc. errors (see output...
Hi
nrf52833 SDK16
The following code works fine on UART 0 but not on UART 1
The problem seems to come from nrfx_uart.c
There is no support for a UART1, so...
Hi,
I've built a project out of the USBD_ACM_CDC example in which I have added a SPI master driver. This project has a timer interrupt that will shoot off every ~500us and...
Hi everyone,
I'm a beginner with nordic development and I managed to screw up my development kit. It started when I was trying to figure out the BLE blinky app with my IOS...
Hi,
I'm working on an IoT project with NRF52832 ( S132) . I need to connect this device to mqtt over 6LoWPAN (IPv6) and run it on a button cell battery CR2032 for as long...
HI,
I am trying to connect to our cloudmqtt account where the topics are dynamically created because of which is it not possible to pre-program a specific topic.
I would...
Hi,
it came to my attention that the inductor Murata LQP15MN3N9B02D (3.9nH) that is used in the antenna matching circuit of the nrf52832 reference design has become NRND...
Hi every one,
I'm a development product with chipset NRF52811, using soft device S112 and SDK 15.3.0.
My device will wake up and send data whenever I press the button...
Hello Nordic Team, I'm starting a project which consist in measure pressure in multiple points and send this data to central unit. At this point, using strain gauges with...
Hi,
I am using the Thingy 91 and I have a program, where I first read GPS, then switch to NBIoT Mode and then send the data to a server.
However if I switch the Antenna...
Hi, Nrf Connect was used as a central.When I send a data (Uart Service) from the app to the characteristic value of a Service (UUID:0x0002), the callback function of another...
Devices: nRF52840
Example: Light switch provisioner/client in one device
I have been looking into provisioner flash storage and am trying to understand at a fundamental...
Hi,
I flashed my 2 PCA10056 boards with light switch server and client respectively. As a provisioner, I am using my IPhone 6 wirh nRF`Mesh app.
After the provisioning...
