Hi, I've encountered a change in behavior when upgrading from NCS 2.9.1 to NCS 3.0.1 regarding MCUboot and watchdog integration. In NCS 2.9.1, I was able to enable the watchdog...
Hello,
On our custom PCB, we’re using an nRF5340 and an nRF7002 via the WM02C module.
In our devicetree, we are using the following QSPI node configuration.
We’ve produced...
Hi,
We are using a modified version of the multi-service sample for nRF9151. Generally, FOTA updates from the nRF Cloud work well.
Once we deploy the FOTA update in the...
Hi, I'm working on provisioning a Pre-Shared Key (PSK) during manufacturing for an nRF5340 device. The device needs access to the PSK at runtime to generate authentication...
I was doing a demo code to implement a wake up triggered by motion. I was able to make it work with the integrated low power accelerometer on thingy52 but it only worked 1...
Hello at all, I try to compile the example peripheral_uart for the nrf54L15-DK. The goal is to compile without west. My directory structure:
where I copied everything from...
Hi,
I`m considerate to use Nordic SoC in my design.
Please advise if Nordic have BLE SoC with Capacitance Touch Sensing capabilities like in Cypress part CY8C4127LQI-BL483...
So, I am adapting and adding to a project based on the example app with SDK16.0 and softdevice s112. I'm using Keil.
My nrf52832 has 256kb flash, 32k ram.
I'm compiling...
Are there any examples of how to configure the COEX pins between the 9160 and a 52840 such that each will actually use the signals to start/stop their respective radios? The...
I see references to a get (0x8046), set (0x8047), and status (0x8048) messages for Node Identity. Where could I find documentation about these messages? There is no sample...
What is the purpose/functionality of SWO pin (pin 6) on the Debug In port?
I see it connected to P0.18 on PCA10040 and P1.00 on PCA10056, but I’m developing custom board...
Hi,
Though I could able to successfully provision light and switch using nrfMesh Android application with all elements being configured and also could publish/subscribe...
Hi,
Recently, I am studying the blog as the link below:
https://docs.microsoft.com/en-us/windows-hardware/design/component-guidelines/bluetooth-prepairing
We would like...
Hi all,
On the iOS version of the Blinky APP, there is a statement
Created by Mostafa Berg on 01/12/2017. Copyright 2017 Nordic Semiconductor ASA. All rights reserved...
Hi,
I am using pin 27 as SCL and 26 as SDA on my custom board which is working on 1.8V.
There is no activity on SCL pin, while i am getting correct values on SDA pin when...
How can I read the ICCID (Integrated Circuit Card ID) of the SIM-card?
Normally (with competitive modems) I get the CCID by AT+CCID.
The nRF9160 reponds with +CME: 0 ...
Hi, I would like to develop a BLE central node that sends over UART when a button is pressed. I understand the memory is limited on nRF52810, but I think it'll fit. The example...
I am developing on the nRF52832. I just discovered that if my program enables Access Port protection by writing the UICR at runtime, then the program can still be read out...
Hello,
I want to use a third party bluetooth module (based on Nordic SOC) in my application, so far my understanding is that using your softDevice stack I have to implement...
Hi
My Thingy:52 works perfectly OK with Thingy app on my iPhone.
However when I use the Gateway on my iPhone and then nrf cloud I get an unstable connection on the cloud...