Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi. twi_sensor As an example source, I have 2 pressure sensors. I use sdp800 and icp10101 separately and use it as twi_interface to read the sensor value well. However, we...
If I write the data from NrfConnect App and if I again go to the scanner tab without clicking on disconnect or killing the app and then if I click scan or refresh option,...
I want to transfer files to uart using ymodem protcol.
For example, when nRF52840 receives a file through BLE,
it tries to send the file back to the device connected to...
Is there a sure fire way to know for sure that my PSM configuration is correct on the nrf9160DK? I'm trying to get LTE-M + GPS working and I'm still not sure if I'm in PSM...
Hello,
We used the Nrf52810 in our project.
Currently, we found a issue: The ble is disconnected when we press the chip. Because our buttons are on top of the chip. We...
When I use circuit configuration no.5, VDD connected to VDDH and have 5V going into VBUS, I see a 1.6V output from the VDD_nRF (VDD/VDDH).
Normally when I connect a battery...
This question is a follow on to https://devzone.nordicsemi.com/f/nordic-q-a/38085/how-to-create-a-copy-of-examples-project---segger-embedded-studio .
It's clear that making...
Hi,
Can i use nRF52840 Pre Development kit as a sniffer.
Also can i use it to program my customized PCB
Note: I need to do both of above urgently so i cannot wait to...
nrf connect sdk version :1.2.0
application:nrf_: desktop
I use command " west build -b nrf52840_pca20041 -d build_pca20041" , but it report error at last.
I don't know...
Hello
Currently, there are systems that operate with peripherals developed with nRF52832, SDK v.12.2.0. I have a question about supporting this for meshes.
1. Are you...
Hello,
I am trying to send a rather large HTTP payload from the nRF9160, the payload is about 10KB in size. The problem I am running into is that after about ~4KB of data...
I'm actually building a project that need to communicate with sdcard.
i read a lot about that and i'm very confusing when i passed on nordic sdk lot of code and ressources...
Hi all,
I am working on a project which uses a vibration motor. I want the vibration motor to vibrate with different patterns. I have read online that a 20kHz PWM can be...
Hi,
I've found this answer which states that the NUS throughput is around 2-4 kB/sec.
https://devzone.nordicsemi.com/f/nordic-q-a/27044/ble_uart-demo-throughput-is-very...
