Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
If we input 5V DC supply to Vin 3-5V P20, the Bluetooth programming failed at start. But if we input 3.3V DC supply to P21, the Bluetooth programming passed. Is this Vin 3...
Hi, I tested "Simple_coap_client" and "simple_coap_server" on NRF52840 using Threading SDK.
It seems that the route is decided by the leader, can I specify the route?
...
I am making a simple breakout board for the nRF52833 (I'm using Fanstel's BM833 module). This is what my board is looking like. There's a ground plain on the top and the bottom...
I'm trying to send data from a NUCLEO F401RE board with the nRF 52840 DK using UART. Then have the data to be sent to my phone via Bluetooth. I'm starting from the ble_app_uart...
Hi Devzone:
I have a question that may be common for companies distributing hardware containing nrf52840 chips.
I have figured out how to use nrfutil to generate Bootloader...
Hi there,
I connected my nRF5340 PDK to an external target - which was unluckily defective.
Since the external board had its own power supply, there was now either an...
Hello,
i have built my own custom service.
I have 13 characteristics ....
But in NRF Connect on an iphone, i can see 13 characteristics , but only in the first there...
Hi
Technically this is a Zephyr question, but googling the issue gave no success. Also, reading the Zephyr docs gavve me no clue.
I have a custom nrf9160 board with an...
I'm trying to capture events like accessing an invalid idx of a C++ vector
I'm using the method at , like this:
std::vector<int> my_array;
my_array.at(10000);
...
Hi,
I want to use the SAADC to measure the voltage on the VDDH pin. I am using a design based on circuit config #4 and following the SAADC example in the SDK version 15...
Hi,
I am using nRF mesh Android app version 2.1.4
I have flashed the devices with light-switch example application under nRF5 SDK for mesh V 4.0.0 on PCA10040 DK. I'm...
Hi,
I have a custom application running on a custom PCBA using the nRF52840 MCU. The Softdevice (S140, v7.0.1) is also utilised because the main application supports BLE...
Hi,
I am looking for the timing of when a connection event will happened. Radio Notification seems the right method for me since it provide an interrupt right before an...
I'm looking at the feasibility of using extended and/or periodic advertisements from an NRF52 to be received by a cell phone. I've used nRF Connect on a couple slightly older...
