Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I want to interface the nRF5340-PDK board to a different vendor's board that runs at 3.3V.
I'm using the SPI bus to communicate between the two boards
Using the nRF5340...
I don't have absolute proof yet, but I'm 90% certain that the carrier LWM2M (0.8.1+build1) has a memory leak when used with a +CEREG notification level higher than it is expecting...
After much searching this site for a solution I'm at a point were I decided it necessary for me to ask directly.
SDK16.0, S132, windows 10 / SES, nrf52DK
I'm able to connect...
Hello, To contextualize my questions, here is my project : I am working on a mesh network with a proprietary protocol. Each node is stationary. I use the nRF52832 SoC.I use...
Hi everyone!
My simple question is: why does this page no longer available? https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/how-to-connect-nrf91-to-google...
2020-06-08 16:20:39.229628+0530 OperationApp[3306:1831777] [Bearer] Central Manager state changed to .poweredOn
2020-06-08 16:20:39.635195+0530 OperationApp[3306:1831777...
How to add two or more custom characteristics in a custom service? I am able to add characteristics from github.com/.../nRF52-Bluetooth-Course to this tutorial. The same way...
Hello,
I want to start with BLE Mesh development. Therefore I have downloaded the Mesh SDK Version 4.1.0 from the Website and started to build everything. But I have a problem...
Hi I'm using the PCA10056 DK and ran into an issue. I can configure the nrf52 to wake up using input pins(although some pins can't wake it up for some reason), however, when...
Hi,
I looked at https://infocenter.nordicsemi.com/topic/comp_matrix_nrf52832/COMP/nrf52832/ic_rev_sdk_sd_comp_matrix.html and I was wondering if the nRF52832 rev 1 does...
I am using S112 6.0.0 / SDK 15.0.0 for nRF52810.
I decided to use an internal RC oscillator to reduce parts.
However, after changing the setting to LFRC, DTM does not...
Hi,
This is related to this:
https://devzone.nordicsemi.com/f/nordic-q-a/60464/c-pc-app-development-with-nrf52840-dongle
I am now testing the UART communication between...
I would like to print debug messages to a PuTTY console. With the evaluation kit, this is very easy. It is connected to my PC via a USB cable, and I listen to one of the virtual...
Dear Nordic Team,
I have developed a custom board using a nRF52832 QFAAB0 chip.
I am using SDK 15.3 and the ble_template example as starting point of developing my code...
I am connecting 1.8V supply to VDDH and VDD so none of the REG will be on. Will I get 1.8V out on the GPIO? I am trying to connect LED on the pins but with 1.8V out that will...
