I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
When trying to configure custom UUID the nRF Connect, the program fails to find the location of the file.
This is due my username to be "Filipe Aguiar" with a space which...
Hello, Nordic community,
I built and successfully run mqtt_simple project on our MQTT broker using v1.1.0 firmware and NCS.
I edited CONFIG_SERIAL=n in spm and mqtt_simple...
I have one of the nRF52840-preview-dk boards. When I brought up nRFgo and clicked on the board, I was invited to update the JLINK firmware. It was pretty enthusiastic in its...
Hello,
I'm trying to use the zephyr settings module to save bluetooth settings on the nRF9160 DK. I'm using the NCS downstream version of Zephyr . Unfortunately in the most...
1.when i use the example on the dir : examples\ble_peripheral\ble_app_blinky\pca10056\s140\arm5_no_packs
i have sucess flash the softdevice and the app:
the console show...
Hello ...
I'm adding buttonless DFU support to my nRF52810 application using the instructions here . I'm using SDK 15.3.0, SD 112 6.1.1.
First question: These instructions...
I'm using the SPI Manager to send large transfers of data to a graphics controller. What I see is that, once a single byte is transferred, the CS line will continue to pulse...
Hi,
Greetings!
I want to disallow an unknown bluetooth device (like phone, etc) to connect to "secure_bootloader_ble_s132_pca10040" except from a bunch of pca10056 (central...
Again, I'm having trouble with the driver library. Earlier when testing I had SPI working OK as a small standalone test , but now I want to add SPIM to my actual application...
Hi,
two days ago I started checking the usbd_cdc_acm example in order to add usb serial comm functionality to my project. and I have some fundamental (newbie) questions...
Hi all,
I'm trying to add to our application BLE DFU feature. Therefore I'm testing first the secure bootloader example provided in the SDK v16.0.0
I managed to build...
Hi!
I have been using and loving the simplicity brought by the Toolchain Manager (TM).
But now I want to use an application available on the master (Connectivity Bridge...
In an attempt to add a custom UUID to your current project I change NRF_SDH_BLE_VS_UUID_COUNT from 0 to 1. Then loaded the code onto our PCA100040 53822 devkit. At runtime...
Hello I have a nRF9160DK V0.8.5 and downloaded the latest User Guide (V0.9.2) but it does not match my board. Looking at the Revision History section of this document it looks...
Hi!
I've been playing around with the SDK and nrf9160 dk for a week now, and it's a lot of fun.
In the beginning the UART example worked perfectly, and I managed to add...
