Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
I wrote a simple application which updates a 16 bit characteristic as fast as possible (after initializing everything). Similar to the following:
The function called checks...
Hi,
example : nRF5_SDK_15.0.0_a53641a\examples\peripheral\twi_sensor
I am using the HTU21D sensor. I was download the twi_scanner example to scan the HTU21D sensor's slave...
I am having a problem talking to a MMA8653FC 3-axis Accelerometer from NXP.
I never see the clock signal generated.
I am using the nRF52 lib, communicating to a nRF5280...
I am converting the the Project ‘usbd_ble_uart_pca10056_s140’ to pca10059, to download it in the nrf52840 dongle. I followed the steps in the nRF52840 Dongle Programming Tutorial...
Hi,
I have some problems when I tried to compile pc-ble-drivers (C) .
1. When I tried to execute ./bootstrap-vcpkg.bat after I follow the steps:
$ git clone github.com...
I’m studying the NRF9160-DK board - I installed the Basis SIM card and followed the instructions : www.nordicsemi.com/.../GetStarted
I launched the Link Monitor program...
Hello,
My thingy:91 is publishing its messages to nrfcloud (=to the corresponding AWS mqttEndPoint and topics/ I suppose AWS IoT Core).
Now I want to get/process these...
In the example / serial in SES I see the softdevice is loaded as an "additional load file"
$(SDK_ROOT:../../../nRF5_SDK_16.0.0_98a08e2)/components/softdevice/s140/hex/s140_nrf52_7...
I am quite new to the nrf9160. Trying to run the gps example https://github.com/ExploratoryEngineering/nrf9160-gps . But everytime I get an error Failed to start GPS. I am...
Hello, the SDK example ble_peripheral\ble_app_uart includes the code below in order to forward data from the UART over the BLE. What it does is wait for a CRLF, or a certain...
hello
i have created 1 custom service for that created 3 characteristics.
with that 3 characteristics i'm trying to notify by using nrf connect app.
my question is...
We are looking for a BLE-enabled chip which can bind to a smartphone, with the aim of performing proximity tests. to make sure the person in possession of the chip is indeed...
We want to design a small tracker for key rings like car keys etc, it will be linked with mobile app. Is it possible to do so?
Whatever I have read till now is it is possible...
Hi,
We are planning to run the nRF52840 in CKAA configuration 3 (attached) in Normal Mode. When we boot, our regulator will provide VDD = VDDH = 1.8V. Reading through the...
