Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Hello,
I am using an nRF52840 on a custom board, and I want to add the workaround for Errata [87] Unexpected wake from System ON Idle when using FPU . However, the the...
Hi,
I´m trying to flash a custom board with nrf52833 chip with the nrf82833 DK.
How can i make sure, that tha DK board will program the custom board? Currently it...
Why isn't this working?
The MPU_RESET_PIN is set to : NRF_GPIO_PIN_MAP( 0 , 20 )
I can not seem to be able to alter the state of the PIN. Whenever I read the PIN its...
Hello all!
I have a timer that sometimes gets started inside the IRQ of the ESB and sometimes needs to be restarted inside its own IRQ
I'm running it in a "one shot...
Hello
This parameter must be modified e.g. if you have a large number of characteristic in your custom service.
is there a reasoning to calculate this or just "try and...
Hello,
We are developing on the NRF52840, using SDK 15.2.0 and FreeRTOS
We currently have DFU over BLE implemented, but we are strongly considering switching over to DFU...
Hello,
we are developing a firmware for the nRF52840 which requires the use of Bluetooth and the SPIS (SPI Slave) functionality.
We are using S140 & SDK 16.
We encounter...
Hi,
I'm having an issue with using nrfutil to generate a bootloader settings image for loading onto an nRF52840 MCU. The resulting image appears to have the wrong starting...
The SERIAL_OPCODE_CMD_CONFIG_TX_POWER_SET (0x44) is not supported in mesh SDK v4.0.0, so I added the following in the file serial_handler_config.c
#include "core_tx.h" #include...
Hi,
I have an application that needs 256kB of RAM however when I try to compile the code for the application processor it complains that there is only 64kB available....
Hi, I've created a custom service for my application. However, is there any way to give a name to the corresponding UUID? I want the custom UUDI to be appearing for example...
Hi,
I updated Segger Embedded Studio to the latest version, 4.50, after that it asked me to update JLINKv6.62a firmware update, but there after I had problems with the board...
Cortex M33 applications on the Thingy-91 - are we able to write any application program that would normally run on a standard M33 ARM processor (off the shelf) - or are there...
Hi I m new to Nordic products and I m just evaluating the nrf5340-PDK.
is it possible to enter in SYSTEM OFF and wake up the CPU with RTC0 or RTC1 interrupt?
How To do...
