I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hi,nordics
I failed to find primary service successfully .The sdk version is 10.00 and I reffered to the example is ble_app_uart_c_s120.The pripheral is a gamepad .I can...
Hello there,
I was wondering if there's a known issues page fro SDK 14.0.0 (not alpha).
Issue #1: crypto compile error:
I ran into an issue compiling nrf_crypto.c
...
Hi everyone,
Does anyone have the beginner tutorials about BLE migrated to SDK 14?
I am specially interested in those about services and characteristics:
devzone...
what command did "nRF Connect" do, after I click "YES" ???
Im stranded in this example : “ble_app_alert_notification”
I don't know how to use "nRF Connect"
when I...
Hey Dev Zone!
I'm attempting to flash FW onto the Thingy via the nrf52840 dev board (which includes JLink). I connected P19 header on nrf52840 to P9 on the Thingy. I downloaded...
I am trying to run below 10 uA with code below while GPIO and uart are on. Sleep mode is applied (below 10 uA), and only wakes up when button is pressed (can be higher amps...
I have a micro connected to the PCA10040. I can use flow control with 5=rts, 6=tx, 7=cts, 8=rx.
Are these pins necessary or advisable for hwfc?
thanks,
Richard
Hello,
I'm having problems getting a stable channel from an Android device (LG K8) and the nRF52 development board. It is hard to tell whether which side is causing the...
I think the answer is mostly no. My application is similar to the Gazell sample projects, it does not use Softdevice. What are the steps to make my application to be compatible...
I loaded the bootloader on the device and it always advertises as DfuTarg even after loading a application that simply blinks an LED. It doesn't seem to switch to the application...
Looking to put this into our new consumer product, and working with a CE/FCC lab. They would like pre-qualification documents if any. I just need to know if they exist and...
Hello, I would like to copy ble_app_uart_c example to a seperate folder and work with that independently. I looked into the following thread and changed my include paths....
Hello
We produced and assembled our own board based on nRF52832-QFAA chip.
It works fine but we want to improve the performance. We heard at the past that we can provide...
To save energy, we want to sent connectable packets infrequently, say once every 10 secs. We also want to send some status info more frequently (once per sec) using non-connectable...
