Hello,*
I'm new to nRF Connect SDK environment, but I'm used to work with Zephyr.
I'm actually confused using west.yml file. I created a new application based on existing...
Hey guys,
I use SDK 3.0.2 and toolchain 3.0.2 and want to start with the modem shell example: https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/cellular/modem_shell...
I made a custon pcb and until now it is working as expected . I am using the me54l14 module by minewsemi and i want to enable the CTE capabilities so that i can have angle...
Help Needed: BLE Not Working on nRF52810 (Tried Zephyr & nRF5 SDK)
Hi everyone, I really need help getting BLE working on my custom board with the nRF52810 . I've been trying...
Hello everyone,
I'm reaching out to this forum in a bit of a bind and hoping someone might be able to offer some guidance or assistance.
I'm trying to download the S340...
Hi, I just tried to connect LSM6DSV IMU with nRF52840dk
The whole folder structure is shown below :
1. I set nrf52840dk_nrf52840.overlay file first.
2. I...
Hello,
We are designing a new Zigbee/Thread end-device sensor and I'm wondering what is the recommended part for it.
I have a demo running with nRF5340 (because the platform...
I am attempting to do some development using the usbd_hid_generic example peripheral code. I am using some C++ libraries in this project, however there is syntax in the usbd...
I would guess that's basically the whole point of the structure, but I want to make sure that the location of the SoftDevice Information Structure and the relative positions...
I want to use the nrf24l01+ with the se2436 apmlifier, but the input of the amplifier requires an input of 100ohms balanced, while the nrf24 has a balanced output of 15ohm...
Hello,
I am using following component for my project, 1-nrf51822,2-SDK 11 3-S130, 4-BLE400 board, 5-Keil IDE. I am also using SDK 11.x HID example for my base program....
Hi,
I try to use the nRF sniffer but it doesn't display anything.
System used :
Windows 10 Family x64
Wireshark 2.4.4
Python 2.7.14 (in C\Python27 included in...
When the Softdevice is not enabled, can the nrf_nvic_ functions be used? When I never enable Softdevice but call err_code = sd_nvic_ClearPendingIRQ(RADIO_IRQn) I get error...
I am working with the DK-52 and SDK 14.2. I am generating two PWM signals using the pwm driver.
Everything works as expected on PINS 11 and 12.
If I change pins to 5...
I'm using nRF52832 SDK board with softdevice s132_nrf52_5.0.0 and SDK 14.2.
The program compile without an error. I tested the led and timer separately and these work.
...
Hey all,
I tried to build my project in the Keil µVision IDE.
But everytime I get the same error and I can't figure out where the problem should be.
I searched for the...
I would like to call sd_power_system_off in my error handler. The product is at a stage where occasional errors still occur as the devices are deployed "in the field" for...
We have a custom board solution with an BLE module from Laird, that uses nrf51822 IC, as a gateway. Code was written in Keil and we used SDK v 8.1.0. Originally we didn't...
According to BLUETOOTH SPECIFICATION Version 5.0 | Vol 3, Part G page 2248
Exchange MTU procedure is initiated by the Cilent, and only be initiated once.
But by looking...
Hi,
I'm trying to add the peer manager to my project, following the guidelines at infocenter.nordicsemi.com/index.jsp
I've copied the peer_manager_init() function exactly...
