Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
I am planning to write a simple OS for nRF51822 based on framed loop principle.
Nothing fancy, just bog standard 10mS frame and optional round robin scheduler.
The questions...
Hello,
I am designing a circuit using the nRF81522 chip.
I was wondering what should I do with the unused I/O pins.
Would it be OK to leave them unconnected, or there...
Hi
Could I use 3.3V to the C3 capacity in the application example,datasheet?That is to say,C3 doesn't connect to VDDPA pin and 3.3V connect to the C3.I found that it is...
We have developed our custom nRF8001 board and connected with Arduino UNO bord. we have used nRF HRM demo application from Github . We are using nRF utility application from...
OK, I didn't read enough fine print before I plunged in, but my version of the nrf51822 I have on a bunch of boards isn't supported by the new SDK.
In a premature onset...
I'm trying to use notifications with Android 4.4. When my service issues a call to sd_ble_gatts_hvx, the result is BLE_ERROR_GATTS_SYS_ATTR_MISSING.
From this link , I...
Hi
when i call twi_master_transfer function in for(;;) loop of file ble_app_hrs project.
Kindly tell me what to do for that.
for (;;)
{
for(i=0;i<10;i++)
{
...
When I plug the PCA10000 into my mac I can see it presents 3 USB interfaces. The first is interface class 0x02, Communication Control, the second is 0x0a, which is Communication...
Hello
I have problem to reach 100 feet and a high data rate using BLE.
I am thinking about using gazell. Is possible to communicate with gaxell protocol to IOS and Android...
Hi guys,
I am trying to get the maximum packet size out of my nrf24 radios. If I am implemeting my own radio protocol which doesnt require 3-5 bytes of address is it possible...
Note that nWP-018 "Migrating to the latest nRF51822 chip version" specifies that the SDK version which should be used with the Eval Kits I have (version 1.0, chip variant...
I'm using the nRF51822 with the version v5.2.1 S110 soft device and have implemented a communication scheme that is very nearly identical to the Nordic UART protocol as implemented...
Hi,
I'm currently working on an Android 4.3 app who must communicate with a model of a specific device.
This device contains a Bluetooth low energy chip nrf8001 and there...
