Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
I modified "pca10001\ble\experimental\ble_app_uart". I add 1 button(app_button.c) and 1 second Timer (app_timer.c)to display clock through UART to PC terminal.
But the...
Hello,
I'm having a problem with the search timing out, channel closing and not being able to reopen the channel after the sd_app_evt_wait command. How do I wake it up without...
Hi,
I am a beginner with nRF51422 (with Keil v 5.10). I am using PCA10006 and PCA10007 together with ANTware II software to evaluate ANT capabilities before I will integrate...
Hello all,
I am developing application for humidity measurement using nrf51822 evaluation board which uses custom services which i have developed. I have already tested...
I have re-targetted the S120 HRM Central to run on the PCA10001 and the only changes necessary were to re-define the LEDs and buttons. It compiles and runs with the following...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi,
I have a full working ble code form the example provided (keil), but I DO NOT SEE any uart interrupt happening. I can write data to the uart, but I can't see any interrupt...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
I am using hw TWI with the s110_nrf51822_6.0 softdevice, nrf51_sdk_v5_2_0
I am using pin 3 scl and pin4 sda of the nrf51[48]22 eval boards.
I am able to drive these pins...
Hi all!
As we know, the funtion Nordic offer to send the ble data is called "sd_ble_gatts_hvx()". But as far as I observe, this funtion just puts the data in the stack...
Hi,
Need to talk between 2 devices using BLE, so for now I have a device with a service and advertising, but now I need the other one to work as central and connect to...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi,
sorry if this is a stupid question, but i'm fairly new to BLE (nRF8001), and even newer at report descriptors.
I'm trying to send some media keys, just volume up...
