Hi
sdk:17.1 ble_app_uart(esb_timeslot))
When I was conducting the integration test between my device (nRF52832) and the external device (nRF24L), I encountered a problem...
HI Teams
I found in the datasheet that the UART, I2C, and SPI on the nRF5340 share the same set of IDs. Does this mean that these three buses cannot be used simultaneously...
Hi，
I am using nRF54L15-DK for Zigbee light_stwitch startup testing. After successfully connecting the development board to the Hub for the first time, I evaluated the time...
Hi
I have a code previously can be built in NCS 2.91:
However, when I use the new NCS 3.01, it can not be built, the error is:
Could you please help me figure out...
hello everyone I have implemented BLE, ADC, RTC, and UART. After that, my power consumption is around 1.31 mA. Can you suggest possible ways to reduce power consumption or...
Hi, I'm a beginner and I'm trying to run an LED blinking program. However, I'm encountering a device-related error.
I've followed tutorials and installed all the necessary...
I have downloaded nRF connect setup V5.1.0 and nRF command line tools V10.24.2.
downloaded nRF connect extension , SDK pack and tool chain in VS code.
I added the build...
Hi
i'm new in dev zone and i have a question
now i work with nRF8001 and i want to design a pcb for it.
I want to reduce the BOM and for this i want to use only the internal...
Hi,
I am trying to use the DFU example provided in SDK 5.1.0. I have built the example using gcc 4.7.x, and i am also using softdevices 5.2.1. The DFU example has been...
Hi,
I've the need to write a characteristic value of 65 bytes, from my central device (iPhone/iPad) to a nRF51822 peripheral device, so I was looking at this document for...
Hi, sorry if this is a dumb question. I've just ordered some development kits and maybe that will answer the question, but i'm being a bit impatient!
I want to put an nrf51422...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi all,
In my project ,I use the SPI to communication between nRF51822 and STM32,but I don't know
how does the heart_rate data transmit to BLE stack.
I am confused...
We have a custom nrf15822-AA board flashed with the S110 (6.0.0) and our application. It has a 32khz crystal. It is connect to our (Mac) development systems with a SEGGER...
I use 51422 with ANT function. When I set a command like "sd_ant_channel_unassign", how can I get response from on_ant_evt callback?
I need to do something after ANT unassign...
I have a nRF8002, I use nRFgo Studio to program the board, and Master Control Panel on Windows to check it board values.
I would like to be able to recognize when the nRF8002...
As the network speed is so low that I often cann't access www.nordicsemi.com, especially on weekends.
Could you tell me the reason?
Note:
At the time when I can...
I am successfully communicating through nrf 8001 chip and i using this module. Now i want to write services and characteristic to this module through iPhone after getting...
Hello：
1.
I used connect Master Control Panel and ble_app_cscs services see the following received some data not understand do not understand, here's UUID I did not see...
Hi all,
I have various questions regarding the softdevices, memory management and power consumption of the nrf51822 chips.
The project we are working on will need to...
I am working on nRF24LE1 boards. I am trying to talk between two boards. I have loaded "enhanced_shockburst_ptx_nrf24le1" and "enhanced_shockburst_prx_nrf24le1" on two different...
I saw an ANCS examples in sdk5.1.0(softdevice=6.0.0), and then I put this example to port to sdk4.4.2 (softdevice=5.2.1) and the example worked perfectly. But when I put the...
