Dear reader,
I am currently working on a project using the NRF54L15 MCU. There is plenty of documentation available for this component, and the reference circuitry for the...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
Hi everyone,
I'm working with the nRF9160 and trying to configure P0.19 as the UART TX pin using Zephyr. Here's the configuration I used in the device tree:
uart1_default...
I have shifted from silicon labs for BLE project. In Si labs we have burn BLE bootloader and BLE application separately. Do i need to do the same here in nrf controller? If...
Hello,
I am using nRF Connect SDK v3.0.1, together with the Find My add-on. Test case TCG013 of the Find My Network Self-Certification Test Cases R1.7 is failing on the...
I am unable to detect any i2c device when connected to the Nordic nRF54L15 DK kit. I have change the voltage from 1.8v to 3.3v and Tried and explore other pins in Port 0 and...
HI: D:\ncs\v3.0.0\nrf\samples\bluetooth\peripheral_uart Using the nrf54l15DK board can run peripheral_uart examples,connection is disconnected. However, when I use the nrf54l05...
I'm planning on testing an rf link with just a pair of NRF24L01+. Having battled with the PTX side and got that working i'm looking at pipes an addresses.
An answer to...
Hi,
Since version v1.16, nRFGo Studio don't start.
The installation is correctly done, but when I launch software nothing occured. I can see it briefly in process list....
The GCC linker scripts included with the nRF51822 SDK (checked: 6.0.0 and 6.1.0 as well as nrf51-pure-gcc-setup ) include .init_array sections , but do not specify them as...
Why does the soft device raise a SWI2 interrupt to indicate to the application that an event occurred? In the SDK, callbacks are implemented using function pointers. A function...
Hi!
I'm launching code from example to NUS (ble_app_uart) on nRF52-DK. Everything is going OK, except when I quickly send 4 packets in row from UART to connected Bluetooth...
Hi,
I'm currently working on the project with some hard-timing dependent features. As I've mentioned in another topic, it fails if I have advertising turned on. Turning...
Hi, after I updated my MAC OS X to the latest version EI Capitan, I found my JLink commander cannot connect to the PCA10001 board again even with the Jlink commander updated...
I read somewhere that to get the callback working on pstorage write, read etc, you need to call pstorage_sys_event_handler() in a function set by softdevice_sys_evt_handler_set...
Hi,
Each Gazell device has unique address identifier (i.e. base address + prefix) mapped for each pipe. How about the host?
For example:
Device that transmits on pipe...
Hi,
Each Gazell Device has an unique address identifier (base address + prefixes), what is the default address identifier for the HOST?
For example
Gazell device transmits...
Hi,
I'm having trouble with how to begin debugging a hard fault error in my code. When I run the debugger, it always ends in the HardFault_Handler in arm_startup_nrf51.s...
I am developing a project by employing nRF51822 and my code is based on ble_app_uart. I met an issue that if there is no device connects to nRF51800 in 3 minutes, the program...
The nrf51 ARM Cortex-M0 processors, according to the documentation, are "code compatible with Cortex-M3". Does this mean they implement LDREX/STREX instructions for atomic...
Hei,
We would be using nrf52 chip in a very miniature device that should have both BLE and NFC capability. NFC is needed for just as a tag. Thus, nrf52 is a good option....